FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Dentures
Flexible

Valplast Denture Case: A Lower Partial With Tight Bite Clearance

This Valplast denture replaces #19 and #20 on the lower left. The dentist wanted it free of metal, with the neighboring teeth left alone. Then the bite scan came in tighter than a Valplast partial denture likes, so we stopped before making anything and went back to the dentist.

Final design · lower left · #18–#21
#18
Gum-colored clasp
#19–#20
Denture teeth
#21
Low clasp
Unilateral, no lingual bar, no metal
Teeth A3.5, base Standard Pink

Valplast Partial Denture Case at a Glance

Classification
Kennedy Class III
Clasps
Gum-colored, on #18 and #21
Denture teeth
VITA
Records received
Intraoral scans of both arches, bite scan, shade and smile photos, Rx form

Patient Situation

The patient lost #19 and #20 about nine months before the case reached us, so the ridge had already settled. The dentist’s chart noted a metal allergy . The records showed:

Span: two teeth, with natural teeth on both sides.
Abutments: #18 and #21 are natural, uncrowned, and not mobile, with stable periodontal findings per the dentist's notes .
Ridge: broad and even along the whole span .
Opposing arch: #14 had drifted down about 1 mm into the empty space.
Overbite: 2.5 mm , so no deep-bite issue up front.
Smile: #21 shows at full smile. #18 doesn't.

What the Dentist Asked For

The Rx for this Valplast denture, condensed :

Valplast base and clasps. No metal anywhere.
Certificate of Authenticity with the case.
Unilateral design, no lingual bar.
No rest seats, no prep on #18 or #21.
Keep the #21 clasp as low on the tooth as retention allows.
Denture teeth in A3.5, tissue in Standard Pink.
Light contact on #19 and #20 when closing, nothing in side movements.
Ship within 8 working days.

The Technical Problems in This Valplast Partial Denture

Not enough height for the #19 tooth

Valplast holds denture teeth mechanically, not chemically. Resin flows through holes in each tooth, usually T-shaped ones, which is why interarch space under 4 mm is a contraindication. Too little room, and a tooth can come loose. A common rule of thumb calls for about 5 mm of posterior clearance.

We measured 4.3 mm at #19 in the closed position, and 5.6 mm at #20. So #20 was fine. #19 sat above the floor but under the rule of thumb.

A shallow undercut on a tooth in the smile

Retention in a flexible clasp comes from undercut, thickness, and width. One lab study of thermoplastic clasps found Valplast needed more than 0.5 mm of undercut with a 1.0 mm thick clasp, and it suggested 1.0–1.5 mm of thickness for a 5 mm wide arm. That’s test-bench data, not a recipe, but it’s a useful check.

On our first path of insertion, #21 gave us 0.4 mm and #18 gave us 0.7 mm . The easy fix for #21 is running the clasp higher up the tooth, which is exactly where nobody wants to see it.

No rests, so the ridge takes the load

This Valplast partial denture is tissue-borne. Bite force goes through the base into the ridge, not down the abutments. A span this short is about as forgiving as it gets, but the base fit and the occlusion on #19 had to account for it.

What We Sent Back to the Dentist

Tight space is on our list of cases that need design sign-off before production, so we paused this Valplast denture on day 1 . If we’re waiting on a dentist, we follow up every other day until it’s settled. Here, we emailed the measurements and three options:

OptionWhat it meansThe catch
A. Keep the bite as isWe shorten the #19 tooth to fit the spaceLess tooth to hold the resin
B. Reshape #14Dentist removes about 0.6 mm from #14 and sends a new bite scanOne short chair visit, and it touches a natural tooth
C. Titanium framework partialRigid support, with rests and claspsConflicts with Rx items 1 and 4

We don’t make that call, and we never change a material without consent anyway. The dentist picked B, saw the patient the next day, and sent a new bite scan on day 2 . We remounted it and measured again: 4.9 mm at #19, enough room to place the retention properly.

Why a Valplast Partial Denture Fit This Case

Not every flexible case makes a good Valplast partial denture. The Japan Prosthodontic Society’s position paper on non-metal clasp dentures doesn’t recommend flexible designs without a metal framework as definitive dentures, except in limited cases such as metal allergy. This patient’s chart put the case in that exception .

Valplast’s FAQ describes the resin as free of acrylic monomer, with a metal-free coloring agent. The dentist weighed that against the patient’s allergy history . Had there been a free-end saddle, loose abutments, or a heavy bite, we’d have flagged those on the same email.

How We Met Each Requirement

Rx itemWhat we did
1 and 2Used Valplast resin only and recorded the resin details on the certificate
3Kept the base on the left side, around #18 and #21
4Worked with the teeth as scanned and adjusted the path of insertion instead
5Tilted the path about 3° , which raised #21’s undercut to 0.6 mm and let the clasp stay low
6Compared the teeth and base with the shade photos before and after finishing
7Set #19 and #20 on the mounted models and narrowed the #19 chewing surface by about 1 mm

Fitting the retention into the space

Inside this Valplast denture, the #19 space broke down like this: at least 1 mm of Valplast under the tooth, which left about 3.9 mm for the tooth itself. We ground the tooth from the ridge side so its chewing surface stayed intact, then cut the retention holes from that same side. #20 had more room, so it needed less grinding.

Sizing the clasps

The tilted path also took #18’s undercut to 0.8 mm . That’s still moderate, and very deep undercuts are where flexible clasps become a problem. On this Valplast partial denture, we set the #21 arm at 1.2 mm thick and 5 mm wide , and the #18 arm at 1.4 mm thick , since that one stays out of sight and can carry more of the retention.

Making It, Day by Day

Day 3 : design sign-off. The dentist got screenshots by email showing tooth positions, clasp outlines, the base, and the tilted path, and signed off the same day . This digital setup replaced a wax try-in, at the dentist's request .
Day 4 : models and setup. We printed the models, blocked out on the approved path, and duplicated them in stone for flasking . Then we prepared the denture teeth, set them, and waxed the base.
Day 5 : injection. Flasked the wax-up, removed the wax, and injected Valplast resin into the closed flask.
Day 6 : finishing. Valplast doesn't finish like acrylic, so it gets its own burs and polishers . We polished the outer surfaces only and kept the tissue side protected, which is how the fit stays true.
Day 7 : inspection and shipping. Once it passed final inspection, the Valplast denture went into its own labeled pack and out the door, one day ahead of the Rx.

The Finished Valplast Denture

Final inspection on this Valplast partial denture:

CheckResult
Teeth, under finger pressureNo movement on #19 or #20
Base under #19, by caliper1.1 mm
Saddle, by caliper2.0–2.5 mm
Base, under strong lightNo bubbles (internal bubbles mean a remake)
Clasps, by caliperWithin 0.1 mm of the design on both arms
Seating on the modelFull seat, no rocking or lifting edges
Articulating filmMarks on #19 and #20 when closed; none in side or forward movement
Smile photo#21 clasp edge stays below the lip line

At delivery, the dentist told us the Valplast denture seated at the first try. It needed one small tweak: the #21 clasp felt snug, so they loosened it with the hot-water method in Valplast’s clinical techniques .

Ridge changes will affect this Valplast denture over time. With no cross-arch connector, the dentist checked stability at delivery and set the wear instructions, including taking it out at night . Nylon has its downsides too: a literature review on polyamide denture bases reports lower stiffness than PMMA, plus surfaces that scratch more easily and can pick up color.

Sending Valplast Flexible Dentures Cases to Istar Digital

Planning Valplast flexible dentures and not sure the space or undercuts will work? Send the records before you ship anything, and we’ll review feasibility first. Better to catch a problem while it’s still a file, before a model crosses an ocean.

For Valplast flexible dentures, we need:

Scans: both arches and a bite scan through our digital workflow, from 3Shape TRIOS, Medit, iTero, CEREC, Shining3D Aoralscan, or Planmeca. Export PLY if gum color matters.
Or physical records: impressions or models plus a VPS bite, packed per our how-to-send guide. Please skip wax bites, since they soften and distort in transit.
Photos: shade tab beside a neighboring tooth in the same frame, plus a full-smile photo when a clasp might show.
On the Rx form: teeth to replace, "Valplast" written out, tooth and tissue shades, where clasps can't show, any prep you'll accept, any allergy that limits the design, and your need-by date.

Flexible partials generally ship in 5–7 working days, counted from the day we receive the case. Design sign-off can add 1–2 working days.

Who Made It

Our removable department made this Valplast denture: 55 technicians working inside Istar Digital Dental Lab’s four labs in Shenzhen and Huizhou, China. Istar Digital has been at this since 2012 and has about 460 people. Everything from design to inspection happens in our own labs. We don’t outsource. A separate 25-person QC group checks cases before they ship.

The removable department handles about 4,000 cases a month in the slow season and about 6,500 at peak. Istar Digital is an FDA-registered establishment (Registration Number 3039441248), which you can check in the FDA database, and our labs run an ISO 13485 quality management system. For EU clinics, custom-made partials follow the MDR custom-made device procedure.

Valplast Denture FAQ

Is the resin genuine Valplast?

Yes. Ask for the certificate on any case. Each one carries a unique serial number the patient can register with Valplast to check the material and activate the manufacturer’s warranty.

Two separate things. Istar Digital’s warranty on the base is 1 year. If a problem is on our side, like a base that won’t seat, a badly placed clasp, an off bite, or the wrong gum color, we adjust or remake it free. Changing the shade or material later, or asking us to proceed on a poor impression after we’ve flagged it, isn’t covered. You pay to send a case in, and we pay to ship finished work back, remakes included.

Valplast’s own limited lifetime warranty covers breakage of the resin base, not the teeth, and it runs through the dentist and Valplast.

Yes, a Valplast partial denture can get all three, here at the lab. Not chairside, the way you’d reline acrylic. Send the appliance, upper and lower models, and a bite record. Valplast’s impression steps cover the pickup impression for adding a tooth and the closed-mouth impression for a rebase. Plan ahead for the time the patient goes without the partial, because it has to travel to us and back.

Valplast has a care page you can pass along: a denture brush instead of a regular toothbrush, no toothpaste on the appliance, a regular soak in Val-Clean, and keep it in solution or water when it’s out of the mouth.

Cast metal frameworks, acrylic, and other flexible partials. The full range is on our partial dentures page.

Yes, free of charge, if you send us 10 or more cases a month. You can ask before or after we receive the case. We guarantee the ship date, but not the arrival date, because customs times vary.

Send Us Your Next Valplast Denture Case

Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow. Ship us a test case, request the price list, or book a factory or video visit.