Full Cast Metal Crowns, Made in the Alloy Class You Prescribe
Full cast metal crowns cover the whole tooth in a single piece of alloy, with no porcelain layer. Istar Digital Dental Lab makes them for clinics and dental labs in the US and Europe, in predominantly base metal, noble, and high noble alloys. If you need porcelain over metal, see our PFM crowns instead.
Choosing the Alloy for Full Cast Metal Crowns
The alloy class is the first decision on a full metal crown. It sets the crown’s color and chairside handling, the CDT code you report, and much of the lab fee. The ADA classification of casting alloys is based on composition by weight, and only gold and the platinum-group metals count as noble.
High Noble
Composition: ≥ 60% gold + platinum-group metals, and gold ≥ 40%. Gold-based alloys, yellow or white. CDT code D2790.
Noble ("Semi-Precious")
Composition: ≥ 25% gold + platinum-group metals, below high noble. Palladium-silver, palladium-rich, reduced-gold. CDT code D2792.
Predominantly Base Metal
Composition: < 25% noble metals. Cobalt-chromium. CDT code D2791.
Silver Doesn't Count
A silver-palladium alloy can be mostly silver and still fall short of the noble threshold.
"Gold" and "Semi-Precious" Aren't Classes
An alloy with 55% gold and little else fails the 60% rule and is noble, not high noble. “Semi-precious” is lab shorthand for the noble tier.
Color Doesn't Tell You the Class
A white alloy can be high noble if it carries enough gold alongside its palladium. When an alloy sits close to a threshold, the manufacturer’s stated composition decides, not the trade name.
How the Classes Differ in Practice
The preparation and indications are the same across all three classes. The differences show up at seating and in the patient’s history.
Adjustment
Gold is soft, so high noble crowns adjust and repolish quickly. The ADA notes that the hardness of base alloys complicates adjustments, so a CoCr crown takes longer to correct in the mouth. Noble alloys vary widely, and the manufacturer’s data sheet gives the hardness.
Metal Sensitivity
The ADA puts nickel sensitivity at 10–20% of the general population, with oral reactions rarer and less severe. Start from the patient’s history and choose the alloy by its documented composition. We supply nickel-free and beryllium-free alloys, and alloys for other specific allergy requirements.
Cost
Alloy cost tracks noble metal content and the gold and palladium markets, so high noble is usually the most expensive class and base metal the least.
ADA Class and ISO 22674 Type Are Different Things
European buyers often ask about ISO compliance rather than ADA class. ISO 22674 sets requirements and test methods for metallic materials used in dental restorations, with or without a ceramic veneer, along with rules for their marking and instructions for use. It’s a separate system: the ADA class tells you how much noble metal an alloy contains, while ISO 22674 compliance is stated in the alloy manufacturer’s documentation.
When to Prescribe a Full Metal Crown
A full metal crown is still the right prescription for a well-defined group of posterior cases:
Outside the Esthetic Zone
Molars and premolars where the patient accepts a metal surface.
Limited Occlusal Clearance
With no porcelain to make room for, it needs the least reduction of any full-coverage crown.
Cracked Teeth
Cracked teeth that need full cuspal coverage.
Heavy Occlusal Load
Where porcelain chipping is the concern. There’s no veneering ceramic to fracture.
Outside that group, full-contour zirconia crowns and bridges give you a strong, tooth-colored posterior option. If you want a high noble substructure with a porcelain surface, see porcelain fused to high noble metal.
Full Cast Metal Crown Products
Cobalt-Chromium Single Crowns and Bridges
We make CoCr crowns by investment casting or by CAM milling. If your practice requires one route, specify it.
Noble and High Noble Single Crowns
Made in the class you prescribe.
A Named Alloy
If you already work with a specific alloy brand and product, name it instead of a class and we’ll confirm it before production.
Proof That You Got the Alloy You Prescribed
You can’t see an alloy’s composition by looking at a crown, so we document it. For any case, on request, we provide the brand, origin, and batch number of the alloy used, with its certificate and proof of composition.
No Silent Substitutions
If a prescribed alloy is unavailable, we tell you first. Nothing changes without your consent, written or verbal.
Alloys Are Kept Apart
Each alloy is processed in its own zone, with dedicated tools, separate sandblasting and polishing equipment, and sorted recycling, so each alloy keeps the composition on its certificate.
Validated Melting Equipment
Melting and heat-treatment equipment goes through installation, operational, and performance qualification (IQ/OQ/PQ), covering temperature control, vacuum or protective atmosphere, and cast quality, with periodic requalification.
One Case Number From Start to Finish
Each crown is tied to the technicians, equipment, material batches, and inspection results behind it.
Preparation and Rx Details
The tooth preparation guidelines for complete-coverage metal crowns from the Foundation for Oral-facial Rehabilitation summarize the commonly taught values.
You’ll sometimes see 0.5 mm quoted as the minimum occlusal clearance for a full cast crown. Read that as the thinnest metal a lab will accept, not as a preparation target. A crown cast to the minimum has no reserve for adjustment. For gold alloys, a feather-edge margin also works and can save tooth structure on a tipped molar.
On the Rx, Include
If the Clearance Comes Up Short
Our technicians measure the occlusal space on the model before design. If it’s too tight for the crown you ordered, we contact you before going ahead. On request, we pack a note with the finished crown naming the tooth and how many millimeters to adjust. You can also approve the design before the crown is cast or milled. We send screenshots or files by email or in your case group chat, and approval adds 1–2 working days.
Records, Scans, and Sending a Case
Send the prepared arch, the opposing arch, and a bite record, as physical impressions or an intraoral scan. With impressions, use a VPS bite registration rather than wax, which distorts with heat in international transit.
We accept scans from 3Shape TRIOS, Medit, iTero, CEREC, Shining3D, and Planmeca, in STL, PLY, OBJ, DCM, or 3Shape .3oxz, and receive cases through 3Shape Communicate and Medit Link. STL is enough for a posterior metal crown. We check incoming scans within one working day and tell you right away if a finish line, the bite, or the opposing arch needs a rescan. File preparation is covered on our digital dental laboratory page.
Inspection, Turnaround, and Warranty
Inspection
Final release is done by quality inspectors who don’t make restorations. Each crown is checked on the model against the approved Rx and design: marginal gap, internal surface, seating, contacts, centric and excursive occlusion, and the metal itself for porosity, cracks, and distortion. Inspectors work with microscopes, scan comparison, and digital measurement.
Turnaround
Full cast metal crowns take 5–7 working days in the lab, counted from the day we have complete records. Time spent waiting for missing records or design approval isn’t counted, and weekends and Chinese public holidays aren’t production days. Rush service is free for clients who send 10 or more cases a month.
Quotes and Shipping
Quotes are itemized to what you order, and you can confirm the full cost before production starts. When metal prices move, we discuss the change with you and give a week’s notice before prices change. You pay to send impressions or models to us, and we pay to ship finished work back, remakes included.
3-Year Warranty
Crowns carry a 3-year warranty, and so do CoCr bridges. We remake or adjust lab-caused problems free of charge: an open margin or contact, high occlusion, a crown that won’t seat, or visible defects. A remake is charged when you change the material or the case requirements, or when we made the case at your request from an impression we had flagged as unclear.
Who Makes Your Crowns
Our Labs
Istar Digital Dental Lab has made dental restorations since 2012, for more than 50 dental labs, 100 clinics, and 400 dentists. We run four labs in Shenzhen and Huizhou, China, with about 460 staff, including a ceramic and metal department of about 70 people and an independent quality control team of about 25. No case is outsourced. Our crown and bridge dental laboratory page covers the rest of our fixed work.
Registrations
Istar Digital Dental Lab is an FDA-registered establishment, Registration Number 3039441248, which you can check yourself in the FDA establishment registration database. Our device listings cover custom crowns and fixed bridges. For EU clinics, custom-made crowns follow the MDR custom-made device procedure, and our labs run an ISO 13485 quality management system.
Full Cast Metal Crown FAQs
Is a metal crown with porcelain still a full cast crown?
No. Once porcelain is fused to the metal, it’s a porcelain-fused-to-metal crown, generally reported under D2750, D2751, or D2752 depending on the alloy class.
Which cement should I use?
Conventional cements such as glass ionomer or zinc polycarboxylate work well on a retentive preparation, and resin cements are an option. Follow the cement manufacturer’s instructions for treating the alloy surface.
Can you ship finished crowns directly to my client's office?
Yes. We ship to any address you give us, so a dental lab can have finished work go straight to the prescribing clinic. The sender address on the waybill can’t be changed.
Can you keep each dentist's preferences on file?
Yes. Our case system records design preferences separately for each dentist, which helps group practices and DSOs. If you prefer the work of one of our technician teams, we’ll assign your cases to it.
What are your hours, and how quickly do you reply?
Our customer service team works 9:30 a.m. to 6:00 p.m. China time (UTC+8) and stays available until midnight for special or urgent cases. During working hours, technical questions usually get an answer within an hour. Outside them, the time difference can stretch that to 7–8 hours, but never more than 12.
Send Your First Full Cast Metal Crown Case
The quickest way to judge our metal work is one crown on one of your own patients. Single trial cases are welcome, and ongoing partnerships work best with a regular flow of cases.