The Patient: An Old Partial That Showed Wire and Sank When Chewing
The patient lost the upper back teeth over the years and has worn an acrylic partial for 9 years . It was made outside Istar, with wire clasps on both canines and a thick acrylic plate over the whole palate .
Three complaints came in with the case :
Implants had been talked through. The patient didn’t want grafting or the cost, so this was a long-term partial, not a stopgap . The dentist’s notes showed:
What the Dentist Asked For
The Rx, shortened :
Records came as upper and lower intraoral scans with a bite scan, plus a scan of the old partial, front-tooth photos, and a full-smile photo .
The Problem We Found: Two Free Ends and Nothing Across the Palate
This is a Kennedy Class I arch: back teeth gone on both sides, with no tooth behind the gap. Each side of the partial ends in a free saddle.
Here’s what happens with a free end. Every time the patient bites on #3 or #14, that saddle presses down into the ridge. Nothing at the back stops it. So it tips around the last tooth in front, the canine. The canine clasp gets pulled each time.
A metal partial handles this with rests on the teeth and a rigid connector across the palate. Valplast has neither. It’s a nylon, and it’s meant to bend. So all the support has to come from the soft tissue it sits on.
Why a horseshoe makes it worse
Plenty of flexible upper dentures for short gaps can go palate-free. Two long free ends are a different job. With an open palate, the only things carrying the bite are the two ridges and a strip of nylon around the front teeth. The nylon strip flexes, so a bite on one side gets very little help from the other.
We measured what the partial would have to work with :
| Measurement | Reading |
|---|---|
| Saddle length, right / left | 24 mm / 23 mm |
| Ridge width at the first molar, right / left | 6.5 mm / 7.0 mm |
| Room between the ridges and the lower molars, #3 / #14 | 7.0 mm / 6.5 mm |
| Usable undercut, #6 / #11 (distobuccal) | 0.5 mm / 0.5 mm |
| Old acrylic plate thickness over the palate | 2.5–3.0 mm |
Room for the teeth was fine. Support wasn’t. A horseshoe here meant two long saddles on narrow ridges, pivoting on two canines.
The published guidance points the same way. A Japan Prosthodontic Society position paper on non-metal clasp dentures says they should follow the same design principles as metal partials. A 2020 review of nonmetal clasp dentures urges caution beyond short-term use and notes that long-term clinical studies are lacking.
Three Designs, and What Each One Gives Up
We held the case on lab day 1 and emailed the dentist the measurements, the diagram, and three designs :
| Design | What it means | Good | The catch |
|---|---|---|---|
| A. As the Rx | All Valplast, horseshoe, palate open | Matches every Rx item. Nothing on the palate | Least support. Saddles likely to sink like the old ones. Canine clasps take the strain |
| B. All Valplast, full palate | Same material and clasps, base covers the palate back to where the soft palate starts to move | No metal. The palate adds support and ties both sides together | Breaks Rx item 2. The palate is covered again |
| C. Metal framework partial | Cast framework with rests on the canines and a palatal plate | Most support for two free ends | Breaks Rx item 1. Metal clasps on the canines would show in the smile |
The dentist and patient went with B . The patient agreed to judge the covered palate at the wax try-in. If it couldn’t be tolerated there, they’d look at A or C again .
How We Built These Flexible Upper Partial Dentures
A palate that's thin and stays put
Clasps that don't show
Back teeth that don't push the saddles around
Teeth that stay in the base
Valplast doesn’t bond chemically to denture teeth. It grips them by flowing into holes and grooves during injection. So every denture tooth got retention holes and a groove on its ridge lap, cleared of wax before injection . That matters on flexible upper dentures carrying six back teeth. Canada’s Drug Agency reports one 120-patient study with significantly more denture tooth loss from flexible partials than from conventional ones at one year.
What the Wax Try-In Changed
A wax base doesn’t flex like Valplast, so the try-in tested coverage, speech, tooth position, and bite, not grip. The dentist seated it, had the patient talk and swallow, checked closing with articulating film, and took smile photos .
| Item | At try-in | What the dentist asked | Final |
|---|---|---|---|
| Back edge | Patient noticed it on swallowing. Fine after a few minutes | Move it 1 mm forward at the midline only | Moved 1 mm at the midline, sides unchanged |
| Speech | “S” sounds clear. No whistling | No change | No change |
| Covered palate | “Much thinner than my old one” | Go ahead with B | Built as B |
Lab days, start to finish
These are days the case was in our lab. The try-in’s courier days and the dentist’s appointment sit outside them .
The Finished Flexible Upper Partial Denture
Final inspection :
| Check | Result |
|---|---|
| Seat on the model | Full seat, no lifted edges |
| Finger pressure on #3, then #14 | Base stays down on the palate, no tipping at the front |
| Articulating film, closing | Even marks on #4, #5, #12, #13, light on #3 and #14 |
| Articulating film, side movements | No marks on the back teeth |
| Palate thickness, by caliper | 1.4–1.6 mm |
| Teeth, under finger pressure | No movement |
| Tooth–base joints, under magnification | No gaps |
| Base under strong light | No bubbles or cracks |
| Gum margins behind #6–#11 | Base clear of them |
Dentist and patient feedback
The dentist: warmed it in hot water for 30–60 seconds, as Valplast’s clinical techniques describe, and it seated without forcing . One small pressure spot under the right saddle was eased at the two-week check .
The patient: says nobody has spotted the clasps . Chewing on the back teeth feels steadier, and food no longer gets under the back of the partial . Tough meat still gets cut into small pieces .
Six weeks of wear isn’t years , so we won’t promise how long it’ll last. Flexible upper partial dentures on two free ends are a compromise, and the dentist set recalls to check the saddles, the clasps, and the tissue under the base .
Sending Flexible Upper Dentures to Istar
Planning flexible upper partial dentures where the back is free on one or both sides? We offer a pre-shipment feasibility review, so you can send records before deciding anything.
We need:
A flexible partial like this generally takes 5–7 working days, and a try-in round counts inside that. Design sign-off can add 1–2 days, and customs time varies.
Who Made It
Our 55-person removable department made this flexible upper partial denture in Istar Dental Lab’s own labs. Istar has four labs in Shenzhen and Huizhou, China, about 460 people, and has been at it since 2012. Nothing gets outsourced. A separate 25-person QC group checks work before it ships. The removable department handles about 4,000 cases a month in the slow season and about 6,500 at peak.
Istar is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA database, and our labs run an ISO 13485 quality management system. For EU clinics, custom-made partials follow the MDR custom-made device procedure.
Flexible Upper Partial Dentures: FAQ
Can you reline it or add a tooth later?
Yes, both, and it’s lab work. If a front tooth is lost down the line, it can usually be added to the existing partial. Send the appliance, upper and lower models, and a bite record. Valplast’s FAQ warns the patient may go a few days without the partial while it’s out.
What if I keep a design you've flagged?
We make it to your Rx, and you don’t need to sign a risk form. Problems caused by that design, remakes included, aren’t on us. Change your mind before production, and we change the design.
What's the warranty?
1 year. A base that won’t seat, lifted edges, badly placed clasps, an off bite, or the wrong gum color get adjusted or remade free. Changing the shade or material later isn’t covered, and neither is going ahead on a poor impression after we’ve warned you. You pay to send a case in, and we pay to ship finished work back, remakes included.
Valplast’s own limited lifetime warranty is separate. It covers breakage of the resin base, not the teeth.
Is the resin genuine Valplast?
Yes. We can ship a Valplast Certificate of Authenticity with the case, and each certificate has a serial number you can register with Valplast.
What other partials do you make?
Acrylic and other flexible partials. The full range is on our partial dentures page.
Can you rush it?
Yes, free, if you send us 10 or more cases a month. We guarantee the ship date, not the arrival date, because customs times vary.
How does pricing work?
Prices aren’t on the website. Quotes are itemized to your requirements, not one bundled price.
Send Us Your Next Flexible Upper Dentures Case
Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow. Send a test case, request the price list, or book a factory or video visit.