FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Crowns & Bridges
Provisionals

Temporary Canine Tooth Case: A PMMA Crown Built to Test the Guidance

This temporary canine tooth case is a single milled PMMA crown on an upper left canine, #11 (FDI 23). On the Rx, it’s a provisional crown, the kind of resin device FDA describes as made for use until the permanent restoration is ready.

Holding the space wasn’t the real job here. The patient hadn’t had a working canine on that side for years, and the dentist wanted the guidance back. But before committing to ceramic, the dentist wanted to see how the patient lived with it. So this temporary canine tooth had a question to answer, and the final crown got built from the answer.

Final design · temporary canine · #11
#11
Milled PMMA
#12
Clear by 1 mm
#13
Clear by 1 mm
Guidance limit: #6, nothing steeper
Shade A2 body, warmer at the neck

Temporary Canine Case at a Glance

Restoration
Temporary crown, #11, milled PMMA
Wear time
6–8 weeks
Guidance
#12 and #13 clear by 1 mm of left lateral movement
Form
Taken from #6
Margin
Chamfer, 0.5 mm subgingival facial, at gum level lingual
Next step
Copy into a final IPS e.max Press crown

Patient Situation

The patient, in their 40s, broke the tip off #11 years ago . It got a root canal and a composite build-up with a flat incisal edge, and it stayed that way . It looked fine at rest. But it didn’t do anything in a left lateral move.

Here’s what the dentist’s notes and the scans showed :

The left side had no canine contact. In a lateral move, the load landed on the premolars, #12 and #13.
#6 was intact. The right canine still guided, so there was a live reference across the arch.
The smile was high. The patient shows all of #11, right up to the gum.
No grinding reported. No night guard either.
The first temporary kept breaking. The dentist had prepped #11 over a fiber post and composite core, then made a bis-acryl temporary at the chair. The tip chipped twice in 2 weeks.

That chipping makes sense once the tooth is guiding again, since all the lateral contact now sits on a small area. It’s also a fair concern on material alone. One in vitro comparison of three provisional materials measured bis-acryl lowest for flexural strength after storage. That’s bench data, not a verdict on any one temporary, but it was enough for the dentist to send this one to a lab.

What the Dentist Asked For

The Rx, condensed :

Temporary crown on canine tooth #11, milled PMMA, for 6–8 weeks of wear.
Give #11 its guidance back. By 1 mm of left lateral movement, #12 and #13 should be clear.
Use the guidance on #6 as the limit. Nothing steeper than that.
Take form and length from #6. The patient doesn't want it to look bigger or feel thick on the tongue.
Shade A2 body, match #6, warmer at the neck.
Chamfer margin, 0.5 mm below the gum on the facial, at gum level on the lingual.
Show the design before milling.
After the test, copy what works into a final IPS e.max Press crown.

The Technical Problems in This Temporary Canine Tooth

Not enough room on the guiding slope

This was the big one. We loaded the prep scan with the bite and checked the space on the lingual slope, right where #22 would ride during a lateral move. It came to 0.8 mm . Our design target for that spot on this crown was 1.2 mm .

That’s the thinnest part of the crown, sitting under the highest load. And the last temporary had chipped right next to it, at the tip.

A steep slope and a thin feel don't go together

The easy way to get thickness is to build the lingual out. But that makes the slope steeper, which breaks the #6 limit on the Rx. It also fills the lingual concavity, and that’s exactly what feels thick on the tongue.

Mirroring #6 wasn't quite enough

Mirroring #6 gave us a good start for length and tip position. But #11 sits 0.4 mm further facial in the arch than #6 does . A straight mirror would’ve looked bulky at the neck, and with this smile, you’d see it.

Canine guidance wasn't a given

We didn’t just assume canine guidance was the right scheme. A clinical study of lateral contacts found group function more often than canine protection, and most patterns didn’t fit either label. So that’s the dentist’s call, per patient. Here the dentist made it, and the Rx spelled it out, so we designed to the Rx.

Three Ways to Fix the Slope

We posted the clearance map in the case’s WhatsApp group with three options :

OptionWhat it meansThe trade-off
A. Keep the prep, mill it thin0.8 mm on the slopeFastest, but the most likely to chip, and it’s the same problem as before
B. Keep the prep, build the slope out1.2 mm, by moving the lingual surfaceSteeper than #6, breaks the Rx, thicker on the tongue
C. Take 0.4 mm more off the lingual slope1.2 mm with the slope where it should beOne more chair step and a new scan

We recommended C. How much tooth to cut isn’t our decision though, so the call was the dentist’s. Most of that slope was composite core anyway, and the dentist went with C . The new prep scan came in 2 working days later . Lead time counts from complete records, so our clock started on that scan.

How We Met the Rx: Building the Provisional Canine Crown

Design

Our designer built the form from three sources, each for one job :

SourceWhat we took from it
#6, mirroredLength, tip position, the limit for the guidance slope
Pre-op scan of #11Neck width and emergence, so the facial stayed 0.4 mm in from the straight mirror
Left and right lateral bitesThe path #22 actually travels, for setting the slope

Then the numbers went in :

Guiding slope: at least 1.2 mm of PMMA.
Tip: 1.5 mm thick and slightly rounded, since a sharp tip is the first thing to go.
Lingual: kept the concavity, and left the cingulum no bigger than #6's. That's what the "not thick" line on the Rx came down to.
Lateral contact: only #11 touching #22 by 1 mm of left lateral movement, checked in the virtual articulator.

The dentist got the preview and approved it on working day 2 , with no changes.

Material and milling

We milled it from an Ivoclar PMMA disc in A2 . We stock PMMA from Ivoclar and Aidite. For this provisional canine crown, milling was the easy pick over printing, because of 6–8 weeks of guiding load on a thin slope. A review of 19 studies on CAD/CAM interim restorations came out in favor of milled for fit, strength and color stability. 18 of those 19 were lab studies though, so it’s a reason to choose it, not a promise.

Shade and finish

The dentist sent the natural tooth and the stump in the same frame as a VITA classical shade tab . Those stump photos matter here: the composite core was darker than the dentin, and we’d need that later for the final.

The technician stained the cervical third warmer to match #6, then polished the facial to a high shine. A temporary canine tooth in a high smile has to hold its shade for the whole wear period, and a rough surface picks up stain faster.

Checks before shipping

QC checked this provisional canine crown against the Rx and the approved design: margins, the inside surface, the seat, contacts, the bite in centric, protrusion and lateral moves, form, polish, and no cracks or voids. It shipped on working day 6 in a foam-filled box, with the tracking number sent that day .

Seating and the 7-Week Test (the Dentist's Report)

This is where the temporary canine tooth earned its keep. The dentist seated it with a eugenol-free temp cement and reported back with two changes:

At seating: the first lateral contact felt heavy, so the dentist took about 0.2 mm off the guiding slope . Our slope, set right at the #6 limit, was a little steep for this patient. That's on the design, and it's the kind of thing a test is there to find.
At the week 1 check: the patient thought it looked a bit long in the smile, so the dentist trimmed the tip by 0.3 mm .

Nothing else changed over the 7 weeks . No chips. It never came loose. By the week 1 check, the patient said they’d stopped noticing it on the tongue .

The Finished Temporary Canine Tooth: Targets and Results

Here’s how the provisional canine crown measured up against the design targets :

Design target
Result
Lingual slope at least 1.2 mm as milled
1.2 mm milled, about 1.0 mm after the chairside adjustment
Tip 1.5 mm as milled
1.5 mm milled, about 1.2 mm after the trim
#12 and #13 clear by 1 mm of left lateral movement
Met in the articulator, confirmed by the dentist in the mouth
Guidance no steeper than #6
Met in design, then lowered by the dentist at seating
Margins on the prepared finish line
Met, no margin adjustment
Shade A2 body with warmer neck, matching #6
Accepted by the dentist with no remake
Intact through the 6–8 week wear period
7 weeks, no chips, never came loose
No bulk on the tongue
No complaint after week 1

From the Provisional Canine Crown to the Final Crown

The temporary canine tooth gave us the numbers we didn’t have at the start. At week 7, the dentist sent a scan of the adjusted temporary in the mouth, then a scan of the prep with it off . We laid one over the other. Recording guidance from a provisional the patient has already worn is an established prosthodontic technique, and here we did it digitally.

Temporary as milledFinal crown
MaterialMilled PMMAIPS e.max Press, pressed
Guiding slopeSet at the #6 limitCopied from the temporary after the 0.2 mm adjustment
Tip lengthMirrored from #6Copied from the temporary after the 0.3 mm trim
Facial and neckFrom the designCopied from the scan of the temporary
ShadeA2 body, warmer neckSame target, with the stump shade from the earlier photos factored in

The dentist approved the overlay, and the final shipped on working day 6 . It seated with one small contact adjustment . Nobody had to guess at the slope or the length, because the patient had already tried both for 7 weeks.

Sending a Similar Temporary Canine Tooth

Got a temporary crown on canine tooth #6, #11, #22 or #27 that needs to do more than hold the space? Here’s how it works with us:

Lead time: 5–7 working days at the lab. Asking to see the design adds 1–2 days. Shipping from China comes on top, so book the visit with some room.
Records: intraoral scans in STL, or physical impressions. Use our Rx form, and see how to send a case. We usually check scan files within 1 working day and tell you if anything needs a rescan.
For guidance work, add: left and right lateral bites, a pre-op scan, the other canine if it's sound, and the shade photos.
Write it on the Rx: planned wear time, canine guidance or group function, any grinding or clenching, and whether a final crown will copy the temporary.
References are welcome: an old temporary, a wax-up, a mock-up, photos or a sketch.
Shipping: you pay to send impressions or models to us, and we pay to send the finished work back.

Every step happens in our own labs, with no outsourcing: four of them in Shenzhen and Huizhou, China, running since 2012, with about 460 people, including 100 in design, 70 in milling and 25 in QC. You can book a factory visit or a video visit with sales.

Istar is an FDA-registered establishment, Registration Number 3039441248, which you can check in FDA’s establishment database. The lab runs under ISO 13485, and everything is made to the dentist’s Rx. For EU clients, custom-made devices follow the MDR custom-made device procedure.

Got a temporary canine tooth you’d like to test before going final? Send us the scans and the Rx as a trial case, and we’ll check the clearance on the guiding slope before anything gets milled. Single trial cases are welcome. Send your first case or talk to us.

FAQ

What's the warranty on a temporary canine tooth?

1 year. It’s made for short-term wear, so it doesn’t get the 3 years we give final crowns. Lab-side problems like open margins, open contacts, a high bite, a crown that won’t seat or the wrong shade get remade free. Changing the shade or material later isn’t free, and neither is a remake after you asked us to go ahead on an unclear impression.

No. We make temporaries in composite resin or PMMA, and we can 3D print them too. We won’t swap a material without your OK.

Yes. Scan it in the mouth and send that with the prep scan. We can copy both its form and its guidance.

Yes. We can also supply temporary cylinders, screws and tools, at extra cost.

Please don’t. Wax softens and distorts in transit. Use a VPS bite registration, and VPS is our first choice for the impression too.

Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t promise that.

Quotes are itemized to your Rx, not one bundled price. Ask us for the price list.