Patient Situation
#7 had a root fracture under an old post crown . The dentist took it out and grafted the socket . The plan: implant at about 4 months, crown after that , so the Valplast single tooth denture has to work for roughly 6 months . The patient wanted nothing metal in the smile and didn’t want the front teeth cut for a bridge .
What the dentist’s notes and the models showed:
Records we got: an intraoral scan taken before the extraction, alginate impressions of both arches taken 2 weeks after it, a VPS bite, a shade-tab photo, a full-smile photo, and the Rx form .
What the Dentist Asked For
The Rx, condensed :
Items 2 and 5 pull against each other. Take the arm off #8, and the grip has to come from somewhere else, usually the palate.
The Technical Problems in This Valplast Single Tooth Denture
The arms cover the gum the study measured
Flexible arms look like gum because they run over the gum. On #8, that means a band of resin sitting on the labial margin of thin tissue every day.
There’s exactly one clinical study on this setup. In Zhou and colleagues’ 2011 study, 76 patients who needed a temporary front tooth picked either a Valplast denture or a conventional partial. Another 38 had no temporary at all.
The team measured crown height of the teeth next to the gap on stone models, about 2 weeks after extraction and again at 97–100 days. The Valplast group’s neighbors lost a mean 0.5 mm of gum (range 0.0–1.2 mm). The other two groups: 0.0 mm. The authors judged Valplast unsuitable for a single missing front tooth.
It’s not a strong study. Patients chose their own group, follow-up was about three months, and it doesn’t say how the clasps were designed. But it’s the only one that looks at a Valplast single tooth denture in the front of the mouth, so the dentist needed to see it before deciding where the arms go.
The ridge won't stay put
The impression was taken 2 weeks after extraction, over a fresh graft . That ridge will keep changing for months. A base that fits on day one can leave a gap under #7 by month two, and food goes straight into it. Valplast doesn’t take a quick chairside reline the way acrylic does. Valplast describes rebasing as lab work.
One tooth, held in mechanically
Nylon doesn’t bond to a denture tooth chemically. In a Valplast single tooth denture, the tooth stays in because the resin locks around it. In a one-year study of 120 older adults, the 40 Valplast wearers lost four denture teeth. Those weren’t single-tooth cases, but on this appliance, one loose tooth is the whole job.
What We Sent the Dentist Before Making It
We held the case on lab day 1 and emailed three designs, the study, and the model photo with the gum margins marked.
| A: As written | B: Grip moved off #8 | C: Arms on both, lifted | |
|---|---|---|---|
| Arms | #6 and #8 facial | #6 running back to #5; #8 held from the palatal side | #6 and #8 facial, edge lifted off the gum |
| Resin on #8’s facial gum | Yes | No | Less, but the arm still crosses it |
| Grip | Most | Less in front, made up at #5 | Least: the arms ride high on the teeth |
| Palate | Small | A narrow strap from #5 to #9 | Small |
| The catch | Daily cover on thin gum, right where the study looked | More palate, a longer piece, #5 arm shows in side view | A gap at the arm edge catches food, and the top line shows |
The dentist picked B and asked us to keep the strap from going past #9 . The #6 arm still crosses #6’s gum, but that gum is thick and doesn’t show as much, and the dentist was fine with it .
We also offered two extras, and the dentist said yes to both :
How We Met Each Requirement
| Rx item | What we did | How we checked |
|---|---|---|
| 1. No metal | Base, strap, and arm injected as one Valplast piece | Resin as written on the Rx |
| 2. Arms (changed to design B) | One arm, #6 to #5. No resin on #8’s facial | Design photos approved by the dentist |
| 3. Off the graft | 0.5 mm relief over the socket, light ridge-lap contact | Checked on the model before flasking |
| 4. Copy the old #7 | Tooth shaped from the pre-extraction scan, width matched to the gap | Overlay on the scan, then try-in |
| 5. Little palate | 6 mm strap hugging the cingulums, #5 to #9 | Try-in, speech check |
| 6. Wax try-in | Wax setup sent before processing | Dentist’s photos and notes |
| 7. Lasts to the implant | Base kept even so it can be relined; reline plan agreed | Delivery note |
Holding #8 from the back
On #8, the strap sits on the cingulum, above the palatal gum margin, with a small relief at the margin . It keeps the piece from tipping forward. That’s the job the #8 arm would have done.
The #6 to #5 arm
The arm starts at the gap, runs low across #6, and ends in the #5 mesiofacial undercut . Across #6 it’s 4 mm wide . It widens to 5 mm on #5, where it does most of the gripping . Caliper reading: 1.2 mm thick .
Keeping a Valplast single tooth in the base
We cut a retention groove in the ridge lap of the A2 tooth and cleaned every bit of wax out of it after boil-out . Wax left in a retention area means resin can’t lock in.
The baseline numbers
| Tooth | Crown height at mid-facial, 2-week model |
|---|---|
| #5 | 7.8 mm |
| #6 | 10.1 mm |
| #8 | 10.6 mm |
All values in this table are sample data .
What the Wax Try-In Changed
The dentist seated the wax setup, took full-smile photos, and had the patient read aloud .
| Checked | What it showed | What we changed |
|---|---|---|
| #7 length | 0.4 mm longer than #10 | Shortened it |
| Arm on #6 | Top edge showed at full smile | Lowered it 1 mm |
| Strap edge | Patient felt it on “s” sounds | Thinned and rounded the edge |
| Lip over #7 | Even with the other side | Nothing |
| Shade | A2 read right next to #8 | Nothing |
Wax can’t test grip, so that waited for the final. We sent photos of the changes and got the go-ahead .
Making It, Day by Day
| Lab day | Stage |
|---|---|
| 1 | Survey and design check |
| 2–3 | Wax setup, checked on the articulator, out for try-in |
| 4 | Try-in changes |
| 5 | Flasking and Valplast injection |
| 6 | Finishing and polishing, tissue side protected |
| 7 | Final inspection by our QC team, shipped |
The Finished Valplast Single Tooth Denture
Final inspection found:
| Check | Result |
|---|---|
| Seating | Full seat, no rocking, no lifted edges |
| #8 facial | No resin contact |
| Arm tip | In the #5 undercut |
| Grip by hand on the model | Firm, no binding going in |
| Socket area | Relief present, no contact |
| Base and strap thickness, caliper | 2.0–2.4 mm , no sudden changes |
| Base under strong light | No bubbles |
| #7 under finger pressure | No movement |
| Articulating film | Light mark from #26 on closing, nothing in side moves |
Week 9: the reline
At week 8, food started packing under the Valplast single tooth denture, and it came back to us with a new impression . We relined the base and sent it back . The patient went without it for the round trip .
What it doesn't do
Feedback From the Dentist and Patient
The dentist
warmed in hot water for 30–60 seconds, the way Valplast describes, and in on the first try .
firm with no adhesive. One spot on the strap behind #5 needed easing .
having the designs and the study before anything was made made the talk with the patient easier .
the margins on #6 and #8 looked level with the starting photos. The measured check against the baseline numbers comes at the implant visit .
The patient
noticed the strap when talking for the first few days, then stopped noticing it .
in and out without help after a couple of tries in the chair .
nobody at work has commented on it .
food stopped getting under the tooth .
Sending Us a Valplast Single Tooth Denture Case
Send the records first, and we’ll tell you where the arms can go before anything’s made.
Pack models and impressions the way our how-to-send guide shows. A Valplast single tooth denture generally takes 5–7 working days from the day we receive it, try-in included. Courier and customs time are extra.
Who Made It
Our 55-person removable department made this one in Istar Digital Dental Lab’s own labs. Istar Digital has four labs in Shenzhen and Huizhou, China, about 460 people, and has been doing this since 2012. Nothing gets outsourced. A separate 25-person QC group checks work before it ships. The removable department handles about 4,000 cases a month in the slow season and about 6,500 at peak.
Istar Digital is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA database, and our labs run an ISO 13485 quality management system. For EU clinics, custom-made partials follow the MDR custom-made device procedure.
Valplast Single Tooth Denture FAQ
Can you add a tooth later if a neighbor is lost?
Yes, a Valplast single tooth can take another tooth later. It’s lab work. Send the appliance, models of both arches, and a bite.
Can a clasp be adjusted chairside?
Yes, carefully. Valplast’s clinical techniques page describes warming the clasp in hot water, bending it, and letting it cool. Check with us before you grind anything off an arm.
What cleaning instructions should the patient get?
Follow Valplast’s care page: a denture brush, a daily soak, and keep it wet when it’s out. Toothpaste can scratch the surface.
What's the warranty?
Istar Digital’s warranty on a Valplast single tooth denture is 1 year. A base that won’t seat, lifted edges, badly placed clasps, an off bite, or a gum color you’re not happy with get adjusted or remade free. Changing the shade or material later isn’t covered, and neither is going ahead on a poor impression after we’ve warned you. You pay to send a case in, and we pay to ship finished work back, remakes included.
Valplast’s own limited lifetime warranty is separate. It covers breakage of the resin base, not the teeth.
Is the resin genuine Valplast?
Yes. We can ship a Valplast Certificate of Authenticity with the case when you need one.
What if I keep a design you've flagged?
We make it to your Rx, and you don’t need to sign a risk form. Problems caused by that design, remakes included, aren’t on us. If you’d rather change it, we change it.
Can you make the implant crown when it's time?
Yes. Our implant lab makes the restoration on the implant. We don’t make the implant itself.
Can you rush it?
Yes, free of charge, if you send us 10 or more cases a month. We guarantee the ship date, not the arrival date, because customs times vary.
How does pricing work?
Prices aren’t on the website. Quotes are itemized to your requirements, not one bundled price.
Send Us Your Next Valplast Single Tooth Case
Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow. You can also book a factory or video visit. Other removable options are on our partial dentures page.