FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Dentures
Flexible

Flexi Denture Single Tooth Case: Finding the Grip on #12

This flexi denture single tooth case replaces #12 , an upper left first premolar. The dentist wanted all Valplast, no prep, and nothing across the palate. So one small piece on one side of the arch had to stay put with no metal and no rest seats. Our first survey didn’t find enough grip.

Final design · one-sided flexible partial · #12
#11
Gum-colored clasp
#12
VITA tooth, A2
#13
Gum-colored clasp
#14
Gum-colored clasp
One-sided, Nesbit-type, Valplast, no metal
Gap 7.2 mm wide

Single-Tooth Flexible Partial Case at a Glance

Tooth replaced
#12
Space
Kennedy Class III, natural teeth on both sides
Appliance
One-sided, Nesbit-type flexible partial, interim
Resin
Valplast, no metal
Clasp arms
Gum-colored, on #11, #13, and #14
Denture tooth
VITA, A2
Stages
Wax try-in, then final
Shipped
Lab day 7

Patient Situation

#12 split vertically and came out about 5 months before the case reached us. An implant was the long-term idea, but the patient wanted to wait about a year . A bridge would’ve meant cutting down #11 and #13, and the patient said no to that . So the dentist planned a flexible denture for one tooth to fill the gap for now .

The dentist’s notes and the models showed:

Gap: 7.2 mm wide, with the ridge settled and a shallow facial dip of about 1.5 mm .
#11: natural, no restorations, 10 mm crown height, not mobile.
#13: natural, small occlusal composite, only 5 mm of facial crown height, not mobile.
#14: natural, no crown, 6.5 mm crown height, not mobile.
Gums: stable periodontal findings on all three teeth, per the dentist .
Bite: natural #21 opposite, about 6.5 mm of room for the tooth. #11 and #13 share the load in left side moves .
Smile: teeth show back through #13 at full smile. #14 only shows from the side .

Records we received: stone models poured from alginate impressions of both arches, a VPS bite, a shade-tab photo, a full-smile photo, and the Rx form .

What the Dentist Asked For

The Rx for this flexible partial denture single tooth, condensed :

All Valplast, no metal.
No prep on any tooth.
One side only, nothing across the palate.
Keep clasps as low and as far back as possible.
Firm enough that the patient won't reach for adhesive.
Match #5 in size and shape, shade A2.
Light contact on closing, nothing in side moves.
Wax try-in before processing.

Items 3, 4, and 5 pull against each other. No cross-arch connection means the grip all comes from the teeth next to the gap. And the teeth next to the gap are the ones that show.

Where a Flexible Denture for One Tooth Gets Its Grip

The level-path survey came up short

We surveyed the models with the occlusal plane level first :

SpotCrown heightUndercut, level pathShows at full smile?
#11 distofacial10 mm0.3 mmYes
#13 distofacial5 mm0.4 mmYes
#14 mesiofacial6.5 mm0.6 mmOnly from the side

All values in this table are sample data .

A lab study on thermoplastic clasps says Valplast needs more than 0.5 mm of undercut with a clasp 1.0 mm thick, and recommends 1.0–1.5 mm of thickness on a 5 mm wide arm. It’s bench data, but it gave us a line to check against. #11 and #13 both fell short.

Thinning the arms wasn’t the fix. Valplast warns that changing clasp thickness or gingival reach can alter flexibility.

#13 doesn't have much room

With 5 mm of crown, a 5 mm arm would cover the whole facial surface of #13. A review of nonmetal clasp dentures says short clinical crowns restrict where these designs fit, and this one sits right in the smile. A narrower arm helps the looks, but the same lab study ties retention to arm width too.

No rests, and a small piece

No prep means no rest seats, so a flexi denture single tooth like this one puts its load on the ridge. That same review points out that flexible designs lack occlusal rests and says they aren’t a prudent pick as definitive work. It also advises against them for Kennedy Class I and II. This one is Class III, and an interim.

Size is the other worry. The ACP position statement on posterior single-tooth replacement calls Nesbit-type removable prostheses generally contraindicated because of aspiration risk, and a premolar is a posterior tooth. A clinical report on unilateral partials warns they can come loose and be swallowed or aspirated.

What We Sent the Dentist Before Making It

We paused this flexi denture single tooth on lab day 1 and emailed the survey with a short note. Three things in it:

The risk

We passed along the ACP position and said a metal framework partial with rests or a cross-arch design would be steadier. The dentist kept the one-sided Valplast . The patient had turned down metal and anything on the palate, it’s an interim, and the dentist would cover the risk chairside . Only the dentist has the patient in the chair, so that’s the dentist’s call.

A tilted path

Tip the model about 4° , so the appliance comes in from the palate side and rolls toward the cheek. Coming out, the arms have to move against the facial surfaces instead of sliding off them. Nothing on the other side of the arch gets in the way, because there’s nothing over there. The catch is that the patient has to learn the path.

A longer piece

Run the #13 arm on to #14, which adds a grip that mostly stays out of sight:

Stop at #13Carry on to #14
Base lengthAbout 13 mmAbout 20 mm
Grip points#11, #13#11, #13, #14
What’s goodSmallest pieceExtra grip behind the smile line, and more to handle
The catchAll the grip sits in the smile on two shallow spotsMore material for the tongue and cheek to notice

The dentist said yes to both and asked to see it at try-in . A bigger piece isn’t swallow-proof, and nobody pretended otherwise.

How We Met Each Requirement

Rx itemWhat we didHow we checked
1. All ValplastBase and arms injected as one pieceResin as written on the Rx
2. No prepUsed existing undercuts onlySurvey on the tilted path
3. One side onlyBase runs #11 to #14 and stops about 6 mm from the palatal gum lineDesign sent to the dentist
4. Low, far backArms sit low on the teeth and #14 carries the rest of the gripFull-smile photo, then try-in
5. Firm gripThree grip points on the tilted path, arms 1.2 mm thickSeated and removed by hand on the model
6. Match #5VITA tooth reshaped to the #5 outline, shade A2Shade photo, model, try-in
7. Light biteLight contact with #21 on closing, none in side movesArticulating film on mounted models
8. Try-inWax setup sent before processingDentist’s marked-up photos

What the tilt did to the numbers

SpotLevel path4° tilt
#11 distofacial0.3 mm0.6 mm
#13 distofacial0.4 mm0.6 mm
#14 mesiofacial0.6 mm0.9 mm

All values in this table are sample data . Each spot got past the 0.5 mm line, and we didn’t have to go looking for anything deeper. We marked the path on the model and wrote the direction on the delivery note , so the dentist could show the patient.

How the arms run

On this flexible denture for one tooth, the #11 arm starts at the gap and wraps the distofacial corner, low on the tooth, 5 mm wide in the first design . The second arm crosses #13 about 4 mm wide, with roughly half of that on the gum . It carries on past the #13/#14 embrasure and ends in the #14 mesiofacial undercut, where it widens to 5 mm . On the palatal side, the base hugs #13 and #14 for bracing . It’s flexible resin, so that helps, but it won’t act like a rigid frame.

Keeping one tooth in the base

Valplast holds a denture tooth mechanically, so we cut a T-shaped groove in the ridge lap , the shape with the best bond in one lab study on Valplast. Wax matters too. A small 18-patient case series of larger dentures saw teeth come loose in four cases, and the authors blamed wax left in the retention areas. Those weren’t single-tooth cases, but on a flexi denture single tooth, one loose tooth is the whole job. We checked the groove after boil-out .

What the Wax Try-In Changed

Valplast suggests a wax try-in before finishing, and the Rx asked for one. The dentist seated the wax setup of this flexible denture for one tooth, took full-smile photos, and sent back notes .

CheckedWhat it showedWhat we changed
#11 armTop edge showed at full smileLowered the edge and narrowed the arm from 5 mm to 4 mm
#12 length0.5 mm longer than #5Shortened it
Side movesContact on #12 going leftTook it out of the move
Palatal baseFine for speechNothing
ShadeA2 read right next to #11 and #13Nothing

A narrower #11 arm gives up some grip. That’s where saying yes to #14 paid off.

Wax can’t test clasps, so the grip had to wait for the final. We sent photos of the changes, and the dentist gave the go-ahead .

Making This Flexible Denture for One Tooth

These are lab days for this flexi denture single tooth. The try-in round sits between days 3 and 4 .

Day 1 : logged the models, surveyed them, emailed the dentist.
Day 2 : got the answer, shaped the tooth, waxed the setup.
Day 3 : checked the setup on the articulator and sent it out.
Day 4 : got the notes, made the changes, sent photos, got the go-ahead.
Day 5 : cut the groove, flasked it, boiled out the wax, injected the Valplast.
Day 6 : finished and polished the outer surfaces, with the tissue side protected so the fit stays put.
Day 7 : final inspection by our QC team, labeled, bagged on its own, shipped.

The Finished Flexible Partial Denture Single Tooth Build

The design goal for this flexible partial denture single tooth: steady on one side of the arch, no metal, no prep, and as little pink as the grip would allow. Final inspection found:

CheckResult
Seating along the marked pathFull seat, no rocking, no lifted edges
Arm tipsIn the surveyed undercuts on all three teeth
Grip by hand on the modelFirm, no binding on the way in
Arm thickness, by caliper1.1–1.3 mm
Base thickness, by caliper2.0–2.5 mm , no sudden changes
Base under strong lightNo bubbles (internal bubbles mean a remake)
#12 under finger pressureNo movement
Articulating filmLight mark on closing, none in side moves
Size and shadeWithin 0.3 mm of #5, A2 against the shade photo

Feedback at delivery

The dentist: warmed it in hot water for 30–60 seconds the way Valplast describes, and it went in on the second try once the path clicked . Retention was firm with no adhesive . One spot on the palatal edge by #13 needed easing .

The patient: got the in-and-out path after a few tries in the chair, and noticed the base for the first few days . The dentist went over taking it out at night and calling right away if it ever felt loose .

Sending Us a Flexi Denture Single Tooth Case

Not sure a flexible partial denture single tooth will hold on your patient’s teeth? Send the records first. We offer a pre-shipment feasibility review for flexible cases, and a design is a lot easier to change before anything’s made.

Models or scans: both arches. Valplast asks for a model poured promptly from alginate.
Bite: VPS, please. Wax softens and distorts in transit.
Photos: shade tab next to a natural tooth in the same frame, plus a full smile that shows how far back the teeth show. Use a 5500K ring or twin flash, not daylight.
On the Rx form: tooth number, "Valplast" written out, prep or no prep, palate or no palate, how far back the arms may go, shades, and whether you want a try-in.

Models and impressions travel best packed the way our how-to-send guide shows.

A flexi denture single tooth generally takes 5–7 working days from the day we receive it, and that includes a try-in. Simple cases can take 2–3. Courier and customs time are separate.

Who Made It

Our 55-person removable department made this flexible denture for one tooth in Istar Digital Dental Lab’s own labs. Istar Digital has four labs in Shenzhen and Huizhou, China, about 460 people, and has been at it since 2012. Nothing gets outsourced. A separate 25-person QC group checks work before it ships, and the removable department handles about 4,000 cases a month in the slow season and about 6,500 at peak.

Istar Digital is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA database, and our labs run an ISO 13485 quality management system. For EU clinics, custom-made partials follow the MDR custom-made device procedure.

Flexi Denture Single Tooth FAQ

Can a flexi denture single tooth be relined, repaired, or added to later?

Yes, all three. Thermoplastic resin doesn’t bond well to reline resins, so it’s lab work, not chairside work. Send the appliance, upper and lower models, and a bite record. The patient goes without it while it’s away.

Yes. Valplast’s clinical techniques page describes heating the clasp in hot water for 60 seconds, bending it, and letting it cool. Go easy, and check with us before you remove any material from a clasp.

Follow Valplast’s care page. It covers a denture brush, a daily soak, and keeping the appliance wet when it’s out. Toothpaste can scratch the surface.

Istar Digital’s warranty on a flexi denture single tooth is 1 year. A base that won’t seat, lifted edges, badly placed clasps, an off bite, or a gum color you’re not happy with get adjusted or remade free. Changing the shade or material later isn’t covered, and neither is going ahead on a poor impression after we’ve warned you. You pay to send a case in, and we pay to ship finished work back, remakes included.

Valplast’s own limited lifetime warranty is separate. It covers breakage of the resin base, not the teeth.

Yes. We can ship a Valplast Certificate of Authenticity with the case when you need one.

We make it to your Rx, and you don’t need to sign a risk form. Problems caused by that design, remakes included, aren’t on us. If you’d rather change it, we change it.

Yes, free of charge, if you send us 10 or more cases a month. We guarantee the ship date, not the arrival date, because customs times vary.

Prices for a flexible denture for one tooth aren’t on the website. Quotes are itemized to your requirements, not one bundled price.

Other flexible partials, acrylic, and cast frameworks. The full range is on our partial dentures page.

Send Us Your Next Flexible Partial Denture Single Tooth Case

Got a flexible denture for one tooth coming up, with shallow undercuts or a short neighbor? Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow. Ship us a test case, request the price list, or book a factory or video visit.