FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Crowns & Bridges
Zirconia

Full Mouth Zirconia Crown Case: 28 Crowns and No Natural Stops Left

This full mouth zirconia crown case covered every tooth in both arches, 28 crowns in all . Once the last provisional came off, not one natural tooth was left to hold the bite. So the real job wasn’t milling 28 crowns. It was making sure the bite the patient had already tested reached our articulator unchanged.

Final design · 28 single crowns, both arches
#2–#15
14 upper crowns
#18–#31
14 lower crowns
No splinting
Vertical raised 2.0 mm at the incisal pin

Full-Mouth Zirconia Crowns Case at a Glance

Restoration
28 separate full-contour multilayer zirconia crowns
Teeth
#2–#15 and #18–#31
Vertical
Raised 2.0 mm at the incisal pin
Provisionals
PMMA at the new vertical, copied once approved
Cause of wear
Acid erosion plus some night grinding
Stumps
All vital, no posts, similar color

Patient Situation

Here’s what the dentist’s notes, scans and photos showed before we planned the full mouth zirconia crowns:

Wear: on every tooth. Flat, short front edges, cupped dentin on the molar cusps, and thin enamel on the palatal of the upper front teeth .
Cause: acid erosion from reflux, plus some night grinding. The reflux had been under a physician's care and stable for over a year before any restorative work .
Old work: composites on most back teeth, a lot of them chipped or stained at the margins .
Teeth: all 28 present, third molars long gone. All vital, no posts, similar stump color .
Bite: the lower face looked short at rest, and there was no room left to restore the front teeth without cutting them shorter .
Patient's ask: stop patching fillings, get some tooth length back, and have back teeth that feel even on both sides .

The European consensus on severe tooth wear says to manage the cause first and put off restorative work as long as you reasonably can. The dentist had done that. The wear had still gone past what fillings could hold .

Why Every Tooth Got a Crown

The dentist planned to raise the vertical. Every tooth that has to carry new height needs a restoration, and here that meant both second molars in each arch too . Leaving the second molars out would have left them out of contact once the bite went up. That’s what makes this a full mouth zirconia crown case and not a “most of the mouth” one. It’s also what made the records hard.

What the Dentist Asked For

The Rx for the full mouth zirconia crowns, condensed :

28 full-contour multilayer zirconia crowns, #2–#15 and #18–#31 (FDI 17–27 and 37–47), all separate, no splinting. No porcelain on top.
Raise the vertical 2.0 mm at the incisal pin.
Wax-up first, then PMMA provisionals at the new vertical.
Copy the provisionals once the patient has worn them and they're approved, including any changes made chairside.
A2 for all 28, a bit more chroma at the necks of the molars.
Canine guidance, back teeth apart in every side movement.
Show the design before milling.

The Records Plan

The dentist sent the record plan with the Rx . It was built around one rule for a full mouth zirconia crown case: never take all the provisionals off at once until the bite is captured.

RecordHow it was takenWhat it was for
Provisional scans, both arches, in closureBefore any final prep scansThe approved target: length, shape, guidance, vertical
Facebow recordSame visitMounting the upper arch
Right segment biteProvisionals off #2–#5 and #28–#31, the rest left inLower position on the right
Left segment biteProvisionals off #12–#15 and #18–#21, the rest left inLower position on the left
Front segment biteProvisionals off #6–#11 and #22–#27, both back segments inLower position at the front
Prep scans, both archesLast, with all provisionals offMargins and inner surfaces
VPS bite for each segmentTaken with each scan bite, sent by courierBackup check. VPS holds its shape in transit, and wax doesn’t

Three segment bites that all agree tell you the vertical survived the switch from provisionals to preps. That’s the whole point of taking three.

How We Built the Full Mouth Zirconia Crown Set

Wax-up and provisionals

We mounted the pre-op models on the facebow record and set the pin at +2.0 mm . A full-mouth bite change gets a semi-adjustable articulator and its own settings, not an average one. The digital wax-up for the full mouth zirconia crowns added 1.5 mm of edge length to #8 and #9, 1.0 mm to the lower incisors, and full cusps back on the molars .

We milled the provisionals from the wax-up in PMMA . A systematic review on raising the vertical found no evidence that an evaluation period improves outcomes, and in its one trial, the removable devices caused chewing, speech and looks complaints. Fixed provisionals were this dentist’s choice, and for a zirconia full mouth rehabilitation they gave us a target better than any wax-up .

The patient wore them for ten weeks . Two things changed chairside, and the dentist wrote both on the Rx update :

What came upWhat the dentist changed
Patient felt #8 and #9 were a touch longTook 0.5 mm off both edges
#11 caught in left side movementsSmoothed the palatal slope of #11

The vertical stayed at +2.0 mm . Both changes showed up in the provisional scan, so we didn’t need anything more than a note telling us to trust the scan over the wax-up.

Checking the bite before any design

With 28 preps in a zirconia full mouth rehabilitation, the bite on the articulator is only as good as the records. So before design, we mounted the lower arch three times, once on each segment bite, and compared where it landed against the provisional reference .

Two out of three matched. The third didn’t :

Segment biteLower arch position vs. the provisional reference
RightWithin 0.05 mm at the pin
FrontWithin 0.05 mm at the pin
Left0.4 mm open at the pin, shifted slightly to the left

That 0.4 mm sounds small. But on the left molars it works out to about 0.2–0.3 mm . If we’d designed to that record, the left crowns would have come out high, and the dentist would have been grinding through the occlusal surfaces of eight brand-new crowns to bring them down.

We can’t tell from the files why it happened. A cheek in the way, a patient who didn’t close all the way, or the software matching the bite scan a little off can each do it. A meta-analysis of full-arch intraoral scans found mixed accuracy results, with most falling within clinically acceptable limits. Most isn’t every one, and that’s why a full mouth zirconia case gets three bites checked against each other, not one bite trusted.

Three ways forward

We stopped before designing a single full mouth zirconia crown and sent the dentist the overlays, the pin readings and three options :

OptionWhat it doesThe catchDentist’s call
1. Wait for the left VPS biteMounts the left side from the physical backup3–4 more days for the courier, and the VPS might show the same problemKept as a cross-check
2. Re-scan the left segment biteNew left record, same method as the othersA short visit, with the left provisionals off againYes
3. Drop the left recordMounts from the right, front and provisional bites onlyThe left preps never get checked in closureNo

The dentist re-scanned the left segment the next day . The new scan landed within 0.05 mm of the other two at the pin . When the left VPS bite arrived later, it matched as well . With both left records now in line with the right and front bites, we started design.

Designing the Zirconia Full Mouth Rehabilitation

Copying the provisionals

We lined the prep scans up with the provisional scans and copied the outer shape of each provisional onto its matching full mouth zirconia crown . The prep scans set the margins and inner surfaces. Everything the patient sees, feels with their tongue or bites on came from the provisionals, including the 0.5 mm off #8 and #9 and the smoother slope on #11.

Design approval

The preview of the full mouth zirconia crowns went out with occlusal, facial and lingual views of both arches, the contact map at the new vertical, and the side movements with the back teeth apart . The dentist asked for slightly wider embrasures between the lower premolars for brushing, then approved it in writing .

Discs, color and finish

All 28 full mouth zirconia crowns came from one material lot . Front teeth sat with their incisal thirds in the more translucent part of the disc, and the molars sat lower, where strength matters more than translucency . With 28 crowns in one smile, small color drift shows, so every crown got the same sintering program and shade reference, and a reference piece went through with each batch .

Finish on the full mouth zirconia crowns was split by zone :

Facial surfaces of the front teeth: thin glaze, polished back to a natural shine.
Every occlusal contact and guidance surface: polished, no glaze.

Every tooth here bites on another crown, and the patient grinds at night. Glaze on a contact gets ground through at the first chairside adjustment and leaves a rough spot. A polished contact can be adjusted and polished again to the same surface .

There’s no porcelain on any full mouth zirconia crown in this case, by Rx. A systematic review of tooth-supported zirconia, pooling 74 publications, found porcelain-veneered zirconia had more failures and complications than monolithic, mostly chipping.

Final checks

Full-mouth work gets an extra review on top of our three QC stages, and two people sign it off . A QC technician who didn’t make the full mouth zirconia crowns checked:

Identity: all 28 against the tooth chart.
Fit: margins, inner surfaces and seating on printed models.
Contacts: all 26 between neighboring crowns.
Bite: at +2.0 mm on the articulator, with centric, protrusive and both side movements.
Against the provisionals: midline, occlusal plane, edge lengths and symmetry, compared with the provisional scan .

QC photos went to the dentist before shipping. The crowns shipped 6 working days after design approval .

The Finished Full Mouth Zirconia Crowns

The dentist seated the full mouth zirconia crowns one arch at a time, upper first . Seating order and cement were the dentist’s choice.

Design target
At seating
Vertical held at +2.0 mm
Shim stock held on both sides, back to the second molars
Left side not high
No left-side adjustment needed
Edge lengths from the provisionals
#8 and #9 matched the provisionals
Back teeth apart in side movements
Clear on both sides
All 26 contacts closed
All 26 right on the first try
Centric
Two small spots adjusted, on #5 and #28, then polished chairside

What the dentist told us

Notes from the dentist after seating :

The re-scan: they'd have missed the left bite. Seeing three overlays side by side made it a ten-minute fix instead of eight high crowns.
Seating: the bite felt like the provisionals the moment the crowns went in, so seating went quickly.
Next step: they ordered a night guard over the new crowns and booked a recall at three months.

What the patient told us

The patient’s comments came through the dentist :

Feel: the full mouth zirconia crowns felt the same as the provisionals, only smoother.
Chewing: even on both sides, with nothing hitting first.
Looks: friends noticed the front teeth looked longer, not whiter.

What This Set Can't Promise

We don’t have long-term follow-up on this full mouth zirconia crown set yet . Published reviews look at single crowns and bridges, not a zirconia full mouth rehabilitation of 28 crowns at a new vertical, so we won’t quote you a survival rate for a set like this.

Send Us Your Full Mouth Zirconia Case

Planning a full mouth zirconia crown case? Here’s what helps us most:

  • Tell us the plan: a tooth chart, the vertical change at the pin, and how you’ll take the bite once the provisionals come off.
  • Rx: use our Rx form. Here’s how to send a case, scans or physical impressions. Digital files go through our digital workflow.

And here’s what you get:

  • Lead time: 5–7 working days at the lab for the final crowns of a full mouth zirconia case. Design approval can add 1–2 days, and time waiting on replies or new records isn’t counted.
  • Shipping: you pay to send work to us, and we pay to ship finished work back, remakes included.
  • Warranty: 3 years on crowns. Open margins, a high bite, a crown that won’t seat, a wrong shade or poor shape all get remade free.
  • Quotes: itemized to your Rx, not one bundled price. Ask for the price list.

Full mouth cases go to a dedicated team in our own four labs in Shenzhen and Huizhou, China. We’ve been at it since 2012, with about 460 people, and nothing gets outsourced. At peak we make about 15,000 zirconia single crowns a month.

Istar is an FDA-registered establishment, Registration Number 3039441248, which you can look up in FDA’s establishment database. The lab runs under ISO 13485. You can also book a factory or video visit.

Have a full-mouth bite change coming up? Send it as a test case. Send your first case or talk to us.

FAQ

What if I want a design you've flagged as risky?

That’s your call, and you don’t need to sign anything. We flag it and ask once. If you still want it, we make it to the Rx. Problems from that choice, remakes included, aren’t ours to cover.

Yes. Ask, and we’ll give you the brand, origin, batch number and certificates for that case. If you want a certain brand, put it on the Rx. We won’t swap a material without your OK.

Yes. If someone on our team has done your earlier cases, you can ask for them again.

Rush is free for clients sending 10 or more cases a month. We guarantee the ship date. Arrival depends on customs, so we can’t guarantee that part.