FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Crowns & Bridges
Zirconia

B1 Zirconia Crowns Case: Four Upper Incisors Beside Natural A3 Canines

These four B1 zirconia crowns went on #7 to #10, the upper incisors (FDI 12 to 22) . Next to them, the natural canines #6 and #11 sit close to A3, and so do the premolars behind them .

So the real job wasn’t making B1. It was making B1 sit next to A3 without the smile looking like it changes color halfway across.

Final design · four upper incisors · #7–#10
#6
Natural · A3
#7
B1
#8
B1
#9
B1
#10
B1
#11
Natural · A3
VITA classical B1 target
Canines and premolars left alone

B1 Shade Zirconia Crowns Case at a Glance

Restoration
Four full-contour multilayer zirconia crowns, #7–#10
Target shade
VITA classical B1
Neighbors
Natural canines and premolars near A3
Stumps
Close to A3; #9 near A3.5 with a fiber post
Approval
Design before milling
Try-in
Pre-glaze, so the patient sees the color first

Patient Situation

Here’s what we had to go on for these B1 zirconia crowns, all from the dentist’s scans, photos and notes:

What was there: #8 and #9 had old PFM crowns with gray showing at the gumline. #7 and #10 had large, stained composite fillings .
Stumps: #7, #8 and #10 are vital and read close to A3. #9 had a root canal, with a fiber post and a tooth-colored core, and reads near A3.5 . Once the old PFMs came off, there was no metal left under any of the four.
Smile: wide. It shows the teeth back to the second premolars, #4 to #13, and the lower incisors show when the patient talks .
Bite: normal overbite and overjet, no clenching noted .
What the patient wanted: brighter front teeth, and B1 by name .

A dark stump or metal core can show through full zirconia. These stumps weren’t dark enough to need masking, which we checked from the stump photos before design. For darker ones, our translucent zirconia crowns case shows how we handle masking.

What the Dentist Asked For

The Rx, condensed :

B1 zirconia crowns on #7 to #10, VITA classical B1.
Natural look. No flat, chalky white.
Leave the canines and premolars alone.
Show the design before milling.
Pre-glaze try-in, so the patient can see the color in their own mouth first.

Full-contour multilayer zirconia on all four was the dentist’s call. The bite was easy, and they wanted one material across the front.

The Technical Problem: B1 Sits Eight Steps Away From A3

VITA’s classical guide has 16 shades. The letter is the hue group and the number is chroma. A dentalcare.com course on the guide describes A as reddish-brown and B as reddish-yellow, and it lays the 16 tabs out lightest to darkest:

TabPlace in the light-to-dark orderWhere it showed up in this case
B11stThe patient’s target
A12ndOne of the options we sent
A25thWhere the lateral necks ended up heading
A39thThe canines, premolars and lower incisors

So B1 next to A3 isn’t one shade apart. It’s eight places apart in lightness, plus a change of hue and more chroma. Put B1 zirconia crowns right against A3 canines and you get a hard line, not a smile.

Some step is normal, though. Natural canines usually read darker and more saturated than the centrals. We weren’t trying to erase the difference. We wanted a step, not a cliff.

Why a B1 shade zirconia crown needs more than a tab

B1 on an Rx is a target, not a recipe. Zirconia crown shade matching starts with the tab, but the same B1 can come out differently depending on the build, where the crown sits in a layered disc, the stain, and whether it’s glazed or polished. Each of those had to be set with the canines in mind.

The Shade Options We Sent

Before design, we sent the dentist three shade plans for the B1 zirconia crowns, with ours marked :

OptionWhat it looks likeWhy it did or didn’t fit
All four straight B1Exactly what the Rx saidThe brightest result, but the biggest jump at #7/#6 and #10/#11
Centrals B1; laterals B1 body with a warmer neck, toward A2Brightest in the middle, stepping down toward the caninesChosen. Keeps B1 where people look first and softens the step
All four A1Closer in hue to the A3 caninesA1 sits right beside B1 in lightness, so it wouldn’t read much brighter, and the patient asked for B1

We also noted that bleaching the canines first would shrink the gap. That’s a clinical call, and the patient turned it down because of sensitivity . So the rest of the zirconia crown shade matching had to happen inside the four crowns.

The dentist talked the options through with the patient and picked the second one. Their reply on the case thread became the working shade plan .

How We Met Each Requirement on These B1 Zirconia Crowns

Reading the records

We got intraoral scans in STL and PLY, a bite scan and the Rx . On front teeth we open the PLY first. Its color shows gum levels and the canines’ surface texture, which an STL leaves out. That’s part of our normal digital workflow.

The shade photos were taken before the prep, with the teeth wet, under a 5500K flash, and with the tabs held in the same plane as the teeth . One shot was taken after the prep, when the teeth had dried out and looked lighter, so we left it out .

CAD design

Our design team set the four crowns up as one group so the midline, lengths and edges line up. We sent a preview and held milling. The dentist asked for the #8 and #9 edges 0.3 mm longer, then approved the design in writing .

What the approved design locked in :

Facial thickness: at least 0.8 mm on all four, with about 1.0 mm on the centrals' middle third.
Margins: followed the chamfer the dentist cut, 0.5 mm under the gum on the facial.
Lateral shape: slightly rounder line angles than the centrals, so the laterals catch less light and look a touch softer.
Contacts: normal against each other and against #6 and #11.

Milling, sintering and color

All four B1 zirconia crowns came out of one multilayer B1 disc, set so the higher-chroma layer sits at the neck . Kuraray’s KATANA FAQ says moving the crown inside the disc changes the gradation you get. The same FAQ sets 0.8 mm as the minimum anterior wall for its UTML and STML discs. Other discs have their own numbers, so we follow the maker’s numbers for whichever disc the case uses.

One disc and one sintering run kept the four crowns even with each other . The program is locked, and shrinkage comes from the zirconia maker’s numbers, checked with test pieces on each batch.

After sintering, the technician stained the laterals’ cervical third toward A2 and left the centrals at B1 . Then came texture: soft vertical lobes and fine lines copied from the canines, cut by hand. A smooth, shiny surface reflects more light and reads whiter, which is the last thing a B1 shade zirconia crown needs next to A3.

We kept the stain on the light side on purpose. Stain can add color, but it can’t take it away, so stopping a little light keeps every try-in change doable .

The pre-glaze try-in

The B1 zirconia crowns shipped on working day 5, stained but unglazed . The patient wore provisionals in the meantime .

The dentist tried them in with water, took full-smile photos with the same flash settings as the pre-op set, and had the patient look in a hand mirror . Here’s what came back :

Checked at try-inWhat they foundWhat we did
Seat, margins, contactsFineNo change
Lengths and midlineFineNo change
Lateral necksStill a touch bright next to the canines at full smile; the patient wanted the laterals to “stop standing out”More cervical stain on #7 and #10
Central surfacesSmoother than the canines; they looked glassy in photosMore texture before glaze

Without this round, those bright lateral necks would’ve shown up after glazing, when they’re much harder to change.

Glaze and polish

The crowns came back to us for a second stage of 2 working days, which made 7 working days at the lab in all, plus one day waiting on design approval . The finish :

Facial: thin glaze, then hand polish down to a medium shine that matches the canines.
Palatal contact areas: polished through the steps, no glaze.
Margins under the gum: polished, no glaze.

Finishing moves color, and a B1 shade zirconia crown has very little room to move. A study of monolithic zirconia found that polishing and glazing both lowered lightness, and glazing also pushed it toward yellow. Kuraray’s FAQ adds that some of its multilayer zirconia comes out more saturated and a bit darker when it’s only polished. So we judge the shade after the last firing, not before.

Final checks

A QC technician who didn’t make the crowns ran the final inspection, with an extra review because it’s front esthetic work. They checked margins, inner surfaces, seat, contacts, and the bite in center and forward movement. Then they checked color, translucency, texture and symmetry under a standard light, against the approved design and the shade plan.

The Finished B1 Zirconia Crowns

Design goal
Where it ended up
Centrals at B1
Matched the B1 tab on the finished crowns
Laterals between B1 and the canines
B1 body, neck reading between B1 and A3
A soft step to the canines
Reads as normal canine color at full smile, not a line
No chalky white
Texture and shine read like the canines in full-smile photos

What the dentist told us

The B1 zirconia crowns seated without any adjustment, and the dentist cemented them with an MDP resin cement .

What the patient told us

Through the dentist, the patient said the smile looks brighter in photos, and nobody has asked them which teeth are crowns .

The trade-offs

Tied to today's canines: the lateral necks were tuned to A3 canines. If the canines get bleached later, those warmer necks could end up reading darker than them .
Time: the try-in added a round trip and a second stage at the lab .

Send Us Your Own B1 Zirconia Crowns

Planning B1 zirconia crowns next to natural teeth that are staying darker? Here’s what helps us most.

  • Characters: if a white spot, crack line or texture is hard to describe, send a picture. You can circle what you want changed on any image.
  • Rx: use our Rx form and see how to send a case. Write “pre-glaze try-in” on it if you want one.
  • Build: full-contour multilayer zirconia or layered zirconia, whichever suits the bite and the look. We never change a material without your OK.
  • Lead time: B1 zirconia crowns generally take 5–7 working days at the lab. Design approval adds 1–2 days.
  • Shipping: you pay to send work to us, and we pay to ship finished work back.
  • Warranty: 3 years on crowns.
  • Quotes: itemized to your Rx, not one bundled price. Ask for the price list.

All of this happens in our own four labs in Shenzhen and Huizhou, China. We’ve been at it since 2012, with about 460 people, and nothing gets outsourced.

Istar is an FDA-registered establishment, Registration Number 3039441248, which you can look up in FDA’s establishment database. The lab runs under ISO 13485. You can also book a factory or video visit.

Got a patient who wants B1 zirconia crowns next to teeth that are staying darker? Send it as a test case, and tell us which teeth aren’t getting work. Send your first case or talk to us.

FAQ

What if the shade is off when the crowns arrive?

If the crowns don’t match the confirmed Rx and shade plan, we remake them free. If the target shade changes after that, it usually isn’t a free remake, though we’ll talk it through with you case by case.

We’d rather you didn’t. Phone filters shift color easily, and that throws off what the technician sees.

Yes. Both are fine as references.

3Shape TRIOS, Medit, iTero, CEREC, Shining3D Aoralscan and Planmeca, plus any scanner that exports open files.

Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t guarantee that.