FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Crowns & Bridges
PFM

Front Tooth Porcelain Fused to Metal Crown Case: Post, Core and Crown Planned Together

This front tooth porcelain fused to metal crown case is a single upper central, #8 (FDI 11), restored with a cast post and core and a PFM crown. It ran in two trips through the lab: the post and core first, then the crown.

Final design · post, core and crown · #8
#7
Natural
#8
Cast post and core · PFM
#9
Natural reference
Porcelain margin labial, metal collar palatal
Nickel-free cobalt-chromium

Anterior PFM Crown Case at a Glance

Restoration
Cast post and core plus PFM crown, #8
Alloy
Nickel-free cobalt-chromium
Shade
A2 body, A3 at the neck, matched to #9
Margins
Porcelain labial, metal collar palatal
Ferrule
About 2 mm labial and palatal, 1 mm mesial and distal
Stump
Gray-brown, darker than #9

Patient Situation

From the dentist’s notes, the records and the photos :

Tooth: #8 was hit in a fall years ago and had a root canal afterward. A large composite buildup broke off, leaving very little crown.
Color: the remaining tooth and root were gray-brown, much darker than #9.
Ferrule: the dentist measured about 2 mm of sound tooth on the labial and palatal and about 1 mm on the mesial and distal, and judged it enough to go ahead.
Neighbor: #9 is natural and healthy, with a clear incisal edge about 1.5 mm deep, a thin white halo along the edge and faint horizontal lines on the face.
Smile: the gum line of #8 shows in a full smile. The gum is of medium thickness.
Bite: normal overbite. The lower right central and lateral, #25 and #26, touch the palatal of #8 about halfway up.
Habits: no clenching or grinding noted.

The patient’s request was simple: a front tooth that looks like the one next to it.

What the Dentist Asked For

The Rx, condensed :

Cast post and core on #8 in nickel-free cobalt-chromium.
PFM crown on #8 in the same alloy.
Match #9: A2 body, A3 at the neck, copy the clear edge and the halo.
Porcelain margin on the labial, metal collar on the palatal.
Same length and outline as #9.

Why an anterior PFM crown fit this tooth

Material was the dentist’s call. With zirconia or glass ceramic, a dark stump and a metal core can show through and change the shade. Under a PFM, the metal coping blocks both. A PFM crown is also usually cemented conventionally, which keeps things simpler on a root-filled tooth with a cast core.

Survival on front teeth has been good. In a cohort of 997 precious-alloy PFM crowns, anterior crowns had 96.4% survival at 5 years and 92.3% at 10 years. That cohort used precious alloy and this crown is cobalt-chromium, so we read it as context, not a forecast.

The Technical Problem: The Root Points One Way, the Crown Another

This is a common snag in PFM crown front teeth work. On upper centrals, the root often leans at an angle to where the crown needs to be. On #8, the canal tilted about 9° toward the lip compared with the crown axis we planned from #9 .

A post has to follow the canal. If the core just carries on in a straight line from the post, it ends up too far toward the lip.

What a straight core would have left

A PFM needs room for two layers on the labial: a coping of 0.3–0.5 mm and front-tooth porcelain of 1.0–1.5 mm. So we aimed for about 1.5 mm in total .

We mirrored #9 to make a digital wax-up of the final crown for #8, then placed a straight core inside it. Here’s what that left on the labial side :

Labial areaRoom with a straight coreTarget
Incisal third0.9 mm1.5 mm
Middle third1.2 mm1.5 mm
Cervical third1.5 mm1.5 mm

With only 0.9 mm at the incisal third, the crown would have had to come out toward the lip, or the porcelain would have been too thin. Thin porcelain over metal looks flat and white, which is the last thing you want next to a clear natural edge.

The Options We Sent Before Casting the Core

We sent the dentist the cross-sections and three ways to build this anterior PFM crown :

OptionWhat it meansThe trade-off
A. Straight core, as isCore follows the postSimplest build, but the 0.6 mm shortfall at the incisal third stays
B. Core angled toward the palate and slimmed on the labialSame post, but the core is turned and shaped to sit inside the planned crownFull labial room, but the core leans on the post, so the dentist has to be happy with that on this root
C. Zirconia post and core with an all-ceramic crownTooth-colored core, an e.max crown or zirconia on topMore light through the edge, but it brings back the masking problem that made the dentist pick PFM

We make all three.

The dentist picked B, but capped the angle at 7° rather than the full 9° . To make up the rest, we slimmed the labial face of the core a little more, keeping it at least 2.8 mm thick from labial to palatal at the incisal third . The dentist approved the design in our WhatsApp case group the next day .

How We Met the Rx

Step 1: Crown first, core second

The crown shape came first: mirrored from #9, then adjusted to #8’s gum line and contacts. The core went inside it, and these are the rooms it left :

AreaPlanned room
Labial, incisal third1.5 mm
Labial, middle third1.6 mm
Labial, cervical third1.5 mm
Incisal, core top to planned edge2.0 mm
Palatal at the #25/#26 contact1.6 mm

That gave the edge space for clear porcelain and kept porcelain on the palatal where the lower teeth touch.

Step 2: Casting and checking the post and core

We poured the canal impression, made the pattern to the approved design and cast it in cobalt-chromium .

Before it shipped, we seated it on the working model and checked that it went to full depth without rocking and that the core matched the design. It shipped 6 working days after approval .

Step 3: Checking the scan of the cemented core

The dentist cemented the post and core, refined the margins and sent a new scan. Before we designed anything else, we measured it against the plan :

AreaReadingOK?
Labial, incisal third1.4 mmYes
Labial, middle third1.6 mmYes
Labial shoulder width1.2 mmYes, for a porcelain margin
Incisal2.0 mmYes
Palatal at the #25/#26 contact1.5 mmYes

The incisal third came out 0.1 mm short of plan. A coping and porcelain at their minimum thicknesses still fit, so we didn’t ask for another adjustment.

Step 4: The coping and the incisal cutback

This is where most PFM crown front teeth cases win or lose the incisal edge. Our coping design for #8 :

Incisal cutback: the coping stops about 1.8 mm short of the edge, so the last part of the crown is porcelain only and can pick up light like #9.
Labial margin cutback: about 1.0 mm back from the margin, so no metal edge sits at the gum.
Support: the coping follows a smaller version of the crown shape, so the porcelain stays even and doesn't sit thick in some spots and thin in others.
Palatal collar: kept thin and low, and well away from where #25 and #26 touch.

We cast the coping, checked its thickness with a caliper, looked at the edges under magnification for flash, and seated it on the model to make sure it didn’t press on the gum. Then it was blasted with aluminum oxide, cleaned in an ultrasonic bath and pre-oxidized so the porcelain bonds well. The porcelain’s thermal expansion is matched a little below the alloy’s, so it isn’t pulled into tension as it cools.

Step 5: PFM Crown Front Teeth Layering, Matched to #9

A technician with more than 10 years of anterior work built the porcelain. The order came from #9, not from the shade tab alone:

Opaque: kept as thin as it could go while still hiding the coping, so the value wouldn't jump above #9 .
Neck: A3-leaning dentin porcelain in the cervical third.
Body: A2 dentin, with soft mamelons cut back into it to leave room at the edge.
Edge: clear incisal porcelain over the cutback, plus a thin opal layer along the very edge for the halo .
Surface: the outline, line angles and faint horizontal lines copied from the photos of #9. If the shape and surface match, small color differences are much harder to see.

We checked the shade against #9’s photos and the tabs under standardized light before and after each firing. We keep a PFM to three or four firings so the shape and color stay stable. This one took three, including the glaze . The layer recipe went into the case record.

Final checks

Glazing can move things a little, so we rechecked the contacts, the bite on #25 and #26, and the margins after the glaze. Then we compared the crown with the approved design and signed it off against the Rx. It shipped 5 working days after we received the core scan .

Finished Front Tooth Porcelain Fused to Metal Crown

Measured at final inspection :

ItemResult
Coping thickness0.4 mm
Labial porcelain1.0–1.2 mm
Clear incisal porcelainAbout 1.5 mm deep, the same as #9
Labial marginPorcelain only, no metal showing

Try-in feedback

The dentist: the crown seated without margin or contact changes. They took a light touch off the palatal where #26 hit first, then cemented it . In flash photos, the neck of #8 read a touch brighter than #9, but at talking distance the dentist couldn’t pick which tooth was the crown .

The patient: happy to smile with their teeth again, and said the edge looked like the one next to it .

What this crown can't promise

A front tooth porcelain fused to metal crown still has metal behind most of the porcelain, so up close it won’t let light through like #9 does. The clear edge helps, but it doesn’t change that.

The root of #8 is also still dark. If the gum moves back past the margin later, the dark root will show, whatever the crown is made of. And the crown depends on the ferrule the dentist kept. A 2026 review of ferrule studies linked 1.5–2.0 mm of ferrule height and about 1 mm of dentin thickness with better outcomes, and found no restorative strategy that matched a natural dentin ferrule. We don’t have long-term follow-up on this crown yet .

Sending a Similar Anterior PFM Crown Case

For the full range of PFM work, see our PFM crowns. For core options, see our post and core service.

Lead time: the post and core and the crown each take generally 5–7 working days at the lab. A design approval adds 1–2 days.
Records: for the core, a scan that reaches the bottom of the post space, or a VPS impression if it doesn't, plus the post length and the ferrule you have. For the crown, color PLY scans with the opposing arch and the bite.
Photos: a 5500K ring or twin flash, with the neighbor and the shade tab in one frame, plus one of the prepped tooth with a tab.
Rx: use our Rx form and see how to send a case.
Alloys: cobalt-chromium, semi-precious and high noble. ADA's alloy classes go by noble-metal content. We never change a material without your OK.
Shipping: you pay to send impressions or models to us, and we pay to ship finished work back.
Warranty: 3 years on PFM crowns and on post and cores. Open margins, open contacts, a high bite, a crown that won't seat or a wrong shade get remade free, and we cover the return shipping. Changing the shade or material later isn't free.
Quotes: itemized to your Rx, not one bundled price. Ask for the price list.

Everything is made in our own four labs in Shenzhen and Huizhou, China, with about 460 people: CAD design, metal casting, porcelain and QC, with nothing sent out. Across the factory, 2–3% of cases come back for a remake. Istar Digital is an FDA-registered establishment, Registration Number 3039441248, which you can check in FDA’s establishment database. The lab runs under ISO 13485.

Have a dark, root-filled front tooth where the root and the crown don’t line up? Send us the records and the Rx. Send your first case or talk to us.

FAQ

Can I send just one test case?

Yes, single trial cases are welcome. Ongoing partnerships suit a regular case flow best, since international shipping is the big cost on one-off cases.

Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t guarantee that.

Yes. On request, we can send the brand, origin, batch number and certificate for the alloy used on your case.

A slightly high bite is fine to adjust chairside. Polish the spot afterward. If you see cracked porcelain, a crown that won’t seat or an open margin, stop and contact us.

Send photos to your case group. If the crown seated well and only the porcelain chipped, we can often remake it from the original data. For a fit, margin or bite problem, we’ll want a new scan, model or impression.