FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Dentures
Metal

Metal Dentures for Front Teeth: Making Room in a Deep Bite

This case is about metal dentures for front teeth where the hard part wasn’t hiding a clasp. It was finding room. The patient lost both upper central incisors, #8 and #9. The dentist prescribed a cobalt-chromium partial and asked us to put the new teeth exactly where the old ones stood.

There was one catch. The patient has a deep bite. The lower front teeth close high up behind the upper ones, right where a denture tooth needs acrylic and retention mesh behind it. We mounted the models, measured, and found there wasn’t enough room for the usual build. So before anything was made, we sent the dentist options.

Final design · upper front · #5–#12
#5
Clasp · rest
#6
Cingulum rest
#7
Natural
#8–#9
Denture teeth
#10
Natural
#11
Cingulum rest
#12
Clasp · rest
Deep bite: about 5 mm overbite
Shade A2 to match #7 and #10

Anterior Metal Denture Case at a Glance

Appliance
Tooth-supported cobalt-chromium partial
Replaces
#8 and #9, set from the pre-extraction scan
Rests
#6, #11, #5 and #12
Clasps
#5 and #12
Shade
A2, matched to #7 and #10
Try-ins
Framework, then wax

Patient Situation

The patient had worn an acrylic interim partial since the extractions. It cracked twice behind the front teeth, in the same spot where the lower teeth close . That told us where the trouble was before we even opened the box.

Here’s what the records showed for these metal dentures for front teeth:

Gap: #8 and #9 missing. #7 and #10, the laterals, are natural, with short roots . The canines, #6 and #11, are sound, and the dentist had cut cingulum rest seats on both .
Bite: deep overbite, about 5 mm . The lower centrals, #24 and #25, close against the palatal side of the gap, about a third of the way up from the gum . In a forward slide, they run along that same surface.
Ridge: settled after the extractions, with mild loss on the labial side .
Back teeth: #2 to #5 and #12 to #15 present and sound, with rest seats prepared on #5 and #12 .
Smile: average smile line. Upper teeth show to the canines at full smile, so clasps on the premolars sit under the lip corners .
Shade: A2 on the laterals and canines .

The pre-extraction scan mattered a lot. It showed where #8 and #9 used to stand, and the dentist wanted that position back.

What the Dentist Asked For

The Rx for these metal partial dentures for front teeth, in short :

Cobalt-chromium framework, tooth-supported, using the rest seats on #6, #11, #5 and #12.
Clasps on #5 and #12, as drawn on the Rx.
Put #8 and #9 back where they were, using the pre-extraction scan. Same lip support.
Keep the patient's bite. Don't open it.
Shade A2 to match #7 and #10.
Something that won't crack behind the front teeth like the interim did.
Framework try-in, then a wax try-in before processing.

Requests 3 and 4 are where it got tight. Request 3 fixes where the front of each tooth goes. Request 4 fixes where the lower teeth land behind it. Whatever we build has to fit in the space between those two.

Why the Usual Build Didn't Fit in This Metal Front Partial Denture

How front teeth usually go on a metal partial

On most metal front partial dentures, an acrylic denture tooth sits on a metal mesh. Acrylic flows through the mesh and locks the tooth on. That needs room behind the tooth for three things: the mesh, the acrylic around it, and the tooth’s own palatal wall.

For this case we planned on about 2.0 mm behind each tooth for the mesh and acrylic, plus at least 1.0 mm for the tooth itself. That’s 3.0 mm in total, measured where the lower teeth touch.

What we measured

We mounted the models with the VPS bite and set #8 and #9 to the pre-extraction scan. Then we measured from the planned labial face of each tooth to the lower incisal edge, at the contact point :

ToothRoom at the lower contactNeeded for a tooth on meshShort by
#82.4 mm3.0 mm0.6 mm
#92.6 mm3.0 mm0.4 mm

So both teeth came up short. Built the usual way, we’d have had to grind the denture teeth thin from behind, and the mesh would end up right under the surface where the lower teeth hit.

Why that matters

That’s the same spot where the interim cracked. Problems with denture teeth and acrylic show up among the most reported technical complications of partial dentures in a 2023 systematic review of technical complications. The review found the data too mixed to give a single rate. For us, the lesson was simpler: don’t put thin acrylic where a lower tooth hits it every time the patient closes.

The Options We Sent Before Making Anything

Before we made any part of these metal front partial dentures, we sent the dentist the measurements, the cross-sections, and four options :

OptionWhat changesTrade-off
A. Build to the Rx as isDenture teeth ground thin behind, mesh close to the surfaceThin acrylic right where the lower teeth land. Same weak spot as the interim
B. Cast metal backingsMetal palatal surfaces on #8 and #9, cast as part of the framework. Acrylic facings in frontPolished metal behind the two teeth, seen in a mirror. Nothing changes from the front
C. Move #8 and #9 forwardTeeth set 0.6 mm (#8) and 0.4 mm (#9) more labialMore lip support than before, and the teeth look pushed out
D. Change the lower teeth or the biteThe dentist shortens #24 and #25, or opens the biteChanges healthy teeth or the patient’s bite. Request 4 said no

Option B keeps both requests. The front of the teeth stays where the scan put it, and the bite stays where it is. Only what’s behind the teeth changes. A cast backing does in 0.8 mm what mesh and acrylic can’t do in 2.0 mm.

We recommended B and said why. The call was the dentist’s, as it is on every case. They approved B in writing the same day . If they had wanted option A, we’d have built it to the Rx after flagging the risk.

How We Met Each Requirement

Each line of the Rx turned into a design choice on this metal front partial denture:

Dentist’s requestWhat we didHow we checked it
Co-Cr, tooth-supportedCingulum rests on #6 and #11, occlusal rests on #5 and #12Rests fully seated on the master model and at framework try-in
Clasps on #5 and #12Placed as drawn on the RxDesign preview approved by the dentist
Teeth where they wereFacings set to the pre-extraction scanScan overlay at design and wax try-in
Keep the biteBackings shaped to the lower contacts as mounted. No change to verticalArticulating paper on the mounted models and in the mouth
Shade A2Facings in A2 , shaped to #7 and #10Shade photo and wax try-in
Won’t crack behind the teethLower teeth close on metal, not acrylicContact marks checked at every stage
Two try-insFramework, then waxDentist sign-off at each stage

The metal backings

Each backing is a cast palatal surface for one tooth, joined to the framework . Here’s how we set them up:

0.8 mm thick where the lower teeth land.
Stops 1.0 mm short of the incisal edge . The edge is acrylic only, so no metal shows from the front.
Facing room: 1.6 mm on #8 and 1.8 mm on #9 . That's enough for the facing to hide the metal behind it.
Junction kept clear of contacts. The line where metal meets acrylic sits away from the lower teeth's marks, both when the patient closes and when they slide forward. The canines take over before the lowers reach the edge .
Retention for the facings: retention beads on the labial side of each backing , then a blasted, degreased surface before processing. The acrylic locks on mechanically.

Holding the bite, not changing it

The Rx said keep the bite. So the backings copy where the lower teeth already close on the mounted models. We didn’t add contacts or take any away. #24 and #25 now land on polished metal, at the same spots they touch on the mounted models.

How We Made These Metal Partial Dentures for Front Teeth

Stage 1: Design, approval, and framework

Records check. Clear rest seats in the impressions, a usable VPS bite, the pre-extraction scan lined up with the master model, photos of the smile. Nothing missing .
Survey and design. We set the path of insertion and drew the rests, clasps, palatal strap, plates against #7 and #10, and the two backings.
Approval. The design went to the dentist with the cross-sections and the options table. Approval adds 1–2 working days, and time spent waiting for a reply isn't counted in the lead time.
Framework and inspection. Our metal department made the framework. Before it shipped, a technician checked it on the master model: smooth seat with no rocking, rests fully seated, clasp form, connector sections, backing thickness with a caliper, and the contact marks of #24 and #25 on the backings.
Shipped for try-in on working day 5 .

Stage 2: Framework try-in

The framework seated with no rocking . One thing came back. In a forward slide, #25 hit the #8 backing harder than #24 hit #9 . The dentist sent a VPS protrusive record .

We remounted with that record and smoothed the #8 backing along the slide path by 0.2 mm . It’s still 0.6 mm thick there . The contacts in the closed bite didn’t move.

Stage 3: Wax try-in

We set the two facings in wax on the backings, matched to the pre-extraction scan and the shade photo. The dentist checked the look, the midline, lip support, speech, the bite, and stability .

Lip support and tooth position were approved as set. One change came back: round the incisal corners of #8 and #9 a little to match #7 and #10 . This stage shipped on working day 2 .

Stage 4: Processing and final checks

Processing. We reshaped the corners and processed the facings and base in Lucitone 199 , with stepped heating and slow cooling, to keep shrinkage and tooth movement down.
Finishing. Only the outer surfaces were polished. The tissue side and borders were covered, so the fit stayed as designed. The backings were polished to a high shine.
Remount and bite check. We remounted the finished partial and checked the bite again in the closed position and in a forward slide.
Final release. Our QC team, which doesn't make the work it checks, signed it off against the Rx. It shipped on working day 4 .

The Finished Metal Dentures for Front Teeth

Design targets vs what we measured

Design target
Checked at final inspection
#8 and #9 at the pre-extraction position
Matched in the scan overlay
Lower teeth close on metal, not acrylic
#24 and #25 marks on the backings, clear of the junction
Backings 0.8 mm where the lowers land
0.8 mm; 0.6 mm along the adjusted slide path on #8
No metal at the incisal edge
Metal stops 1.0 mm short; no gray showing from the front under our shade light
Bite unchanged
Same contacts as on the original mounted models
Rests seated, no rocking
Met
Shade A2, corners matched to #7 and #10
Met
Base
No bubbles under strong light; thickness checked with a caliper

What the dentist told us at delivery

In short :

It seated on the first try. No rocking, and the clasps needed no adjusting.
The bite landed on metal. Articulating paper put #24 and #25 on the backings, right where the preview showed.
From the front, it looked like the scan. The patient's lip looked the same as before the extractions.
The patient noticed the metal with their tongue for a few days, then stopped. Speech was fine.

Here’s what this partial won’t do. It’s still a removable partial. The ridge under it will keep changing, and the dentist plans the recalls. There’s no long-term follow-up on this case yet .

Sending Metal Front Partial Dentures to Us

If you’re planning metal dentures for front teeth in a deep bite, here’s what helps us measure the room before we design anything:

Impressions or scans. VPS impressions of both arches, or scans from TRIOS, Medit, iTero, CEREC, Aoralscan, Planmeca or anything that exports an open file. For front teeth, PLY with color helps. If you've got a scan from before the extractions, send it.
Bite. A VPS bite registration, plus a protrusive record if the lower teeth slide along the palatal side. Please don't use wax. It softens and distorts in transit.
Photos. Full smile, lips at rest, retracted front view, and the shade tab next to the neighboring tooth.
On the Rx. The teeth you're replacing, your rest seats, where clasps can go, whether the bite can change, and the try-ins you want. Use our Rx form, and see how to send a case.

Most metal dentures spend 5–7 working days in the lab, and simple ones 2–3. Each stage of a staged case is scheduled on its own. Metal partials carry a 1-year warranty covering the whole partial, framework included. A partial that doesn’t seat, a lifted border, an off bite, or a clasp placed where it spoils the smile gets adjusted or remade free. You pay to ship the case to us, and we pay to ship finished work back, remakes included.

For the standard alloy, see our cobalt-chromium partial dentures. For other bases and designs, see our full range of partial dentures.

Who Made It

These metal partial dentures for front teeth were made in our removable department, about 55 technicians inside Istar Dental Lab’s four labs in Shenzhen and Huizhou, China. Istar has been making dental restorations since 2012 and has about 460 staff. Design, metal work, setup, processing and finishing all happen in our own labs. Nothing is outsourced. A separate QC team of about 25 does the final release.

Istar Dental Lab is an FDA-registered establishment, Registration Number 3039441248. You can check it in FDA’s establishment registration database. Our labs run an ISO 13485 quality management system, and custom-made dentures for EU clinics follow the MDR custom-made device procedure. You’re welcome to visit the factory or book a video tour.

Metal Partial Dentures for Front Teeth: FAQ

What if I'd rather keep acrylic behind the teeth, even with little room?

Then we make it to your Rx. We’ll flag the risk first, and you don’t need to sign anything. But problems that come from that design, remakes included, aren’t on us.

Yes. We make titanium dentures on pure titanium frameworks, with the same try-in options. Titanium is less stiff than cobalt-chromium, so we’ll tell you how that changes the design before we start.

Yes. We ship the finished framework, backings included, on the master model, and your team sets and processes the teeth.

Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t guarantee that.

We don’t publish prices on the website. Ask for our price list, and we’ll quote each case item by item. Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow.

Send Us Your Next Front Partial

Got a front case where the lower teeth close tight behind the gap? Send us the impressions or scans, a VPS bite and your Rx as a test case. We’ll mount it, measure the room and send you the design before we make anything. You can also request our price list or book a factory or video visit.