The Patient: Two Front Teeth, One Partial, Two Repairs
The patient lost #8 and #9 in an accident years ago . Implants would have needed a bone graft first, and the patient said no . A bridge would have meant crowning #7 and #10, both sound. So 14 months ago they got an all-Valplast partial, made outside Istar .
They liked it. No metal in the smile, light in the mouth . Then at month 9, the #9 tooth came out while they were biting into a sandwich . The dentist put it back chairside with acrylic repair resin. Three weeks later it was out again .
What the chart showed:
What the Dentist Asked For
The Rx, shortened :
Flexible Denture Front Teeth: What the Returned Partial Showed
We looked at the old partial under magnification before touching the scans :
Why the chairside fix didn't hold
Valplast is a nylon. It doesn’t bond chemically to denture teeth. It holds them mechanically, by flowing into holes and undercuts in the tooth during injection. Acrylic repair resin doesn’t bond to it either. So once the #9 socket had no retention form, the acrylic just sat there. It had nothing to grab.
Where the lower teeth were landing
That explained the #9 socket. It didn’t explain why the teeth were working loose in the first place. For that we mounted the intraoral and bite scans the dentist sent, and lined up a scan taken with the old partial seated . The bite is deep.
On closing, #24 and #25 landed on the Valplast just above the joints behind #8 and #9 . In protrusion, #24 slid along the base edge before it reached the #9 tooth . That matched the worn patches.
| Measurement | Reading |
|---|---|
| Overbite | 5.0 mm |
| Overjet | 1.5 mm |
| Lower incisor edges to the palatal gum, teeth closed | 2.6 mm behind #8, 2.0 mm behind #9 |
| Old Valplast wrap behind the teeth, by caliper | 0.8 mm at #8, 0.6 mm at #9 |
| Old denture teeth, palatal thickness at the neck | 1.4 mm at #8, 1.1 mm at #9 |
A thinned tooth and a thin layer of nylon had to share that room. Every bite pushed the lower incisors into that thin nylon right at the joint. Nylon flexes. The tooth doesn’t. Over months, that opens the joint, and a tooth with little left to lock into comes out.
That fits the published data, too. Canada’s Drug Agency reports one 120-patient study with significantly more denture tooth loss from flexible partials than from conventional ones at one year. A Japan Prosthodontic Society position paper on non-metal clasp dentures asks for regular partial denture design rules to apply to them.
Three Ways Forward, and What Each Costs
We held the case on lab day 1 and emailed the dentist the photos, the measurements, and these options :
| Option | What it means | Good | The catch |
|---|---|---|---|
| A. Repair or copy | Reset #9 in the old base, or remake the same design | Fastest. Matches the Rx word for word | Same contacts, same thin wrap. Likely to fail again at the same joint |
| B. All Valplast, rebuilt for the bite | Keep the material, clasps, and look. Change how the teeth sit and how they’re held | Meets Rx items 1–4 | The room is still tight. Lip support changes a little. Less margin than C |
| C. Metal framework partial with metal palatal backings | The lower incisors bite on metal backings on #8 and #9 | Best suited to this bite | Breaks Rx item 1. The clasps would need redesigning |
The dentist talked it through with the patient, and they chose B . If a tooth comes loose again, C is the next step . That’s the dentist’s call.
How We Rebuilt This Flexible Partial for the Bite
Letting the teeth take the bite
Giving each tooth something to lock into
What the Wax Try-In Changed
A wax base doesn’t flex like Valplast, so the try-in tested tooth position, lip, and bite, not grip. The dentist seated it, checked closing and protrusion with articulating film, and took smile photos .
| Item | At try-in | What the dentist asked | Final |
|---|---|---|---|
| Protrusion | #24 caught the wax edge behind #9 before reaching the tooth | Clear it | Base edge moved 0.8 mm toward the ridge |
| Lip | Upper lip felt slightly fuller to the patient | No change | No change |
| Length and shade | Matched the old teeth and #7 and #10 | No change | No change |
Lab days, start to finish
Days the case was in our lab. The try-in’s courier days and the dentist’s appointment sit outside these .
The Finished Partial
Final inspection :
| Check | Result |
|---|---|
| Seat on the model | Full seat, no rocking, no lifted edges |
| Articulating film, closing | Marks on the palatal tooth surfaces of #8 and #9. None on the base |
| Articulating film, protrusion | Lower incisors run on the tooth edges. None on the base |
| Teeth, under finger pressure | No movement on #8 or #9 |
| Tooth–base joints, under magnification | No gaps |
| Base under strong light | No bubbles or cracks |
| Gum margins | Base clear of the palatal margins of #7 and #10 |
| Arms on #6 and #11 | Within 0.1 mm of the old partial’s scan |
Dentist and patient feedback
The dentist: warmed it in hot tap water for 30–60 seconds, as Valplast’s clinical techniques describe, and it seated with the same firm hold as the old one . No bite adjustment was needed .
The patient: says it looks just like the old one, and nobody at work noticed the swap . The fuller-lip feeling was gone by day two .
Sending Flexible Partial Dentures for Front Teeth to Istar
Got flexible partial dentures for front teeth that keep losing a tooth? We offer a pre-shipment feasibility review, so you can send records before deciding anything.
We need:
plus any loose tooth.
both arches with the partial out, closed and protrusive bites, and one with the old partial seated if it still seats, through our digital workflow. Intraoral scans are fine for flexible partials.
models or impressions of both arches with a VPS bite, packed per our how-to-send guide. Please skip wax bites. They soften and distort in transit.
a full smile and a wide laugh.
which tooth came out, when, and any chairside repair, plus “Valplast” written out.
A flexible partial generally takes 5–7 working days, and a try-in round counts inside that. Design sign-off can add 1–2 days, and customs time varies.
Who Made It
Our 55-person removable department made this partial in Istar Dental Lab’s own labs. Istar has four labs in Shenzhen and Huizhou, China, about 460 people, and has been at it since 2012. Nothing gets outsourced. A separate 25-person QC group checks work before it ships. The removable department handles about 4,000 cases a month in the slow season and about 6,500 at peak.
Istar is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA database, and our labs run an ISO 13485 quality management system. For EU clinics, custom-made partials follow the MDR custom-made device procedure.
Flexible Denture Front Teeth: FAQ
Can you reline it or add a tooth later?
Yes, both, and it’s lab work. Send the appliance, upper and lower models, and a bite record. Valplast’s FAQ warns the patient may go a few days without the partial while it’s out.
What if I keep a design you've flagged?
We make it to your Rx, and you don’t need to sign a risk form. Problems caused by that design, remakes included, aren’t on us. Change your mind before production, and we change the design.
What's the warranty?
1 year. A base that won’t seat, lifted edges, badly placed clasps, an off bite, or the wrong gum color get adjusted or remade free. Changing the shade or material later isn’t covered, and neither is going ahead on a poor impression after we’ve warned you. You pay to send a case in, and we pay to ship finished work back, remakes included.
Valplast’s own limited lifetime warranty is separate. It covers breakage of the resin base, not the teeth.
Is the resin genuine Valplast?
Yes. We can ship a Valplast Certificate of Authenticity with the case, and each certificate has a serial number you can register with Valplast.
What other partials do you make?
Acrylic and other flexible partials. The full range is on our partial dentures page.
Can you rush it?
Yes, free, if you send us 10 or more cases a month. We guarantee the ship date, not the arrival date, because customs times vary.
How does pricing work?
Prices aren’t on the website. Quotes are itemized to your requirements, not one bundled price.
Send Us Your Next Flexible Denture Front Teeth Case
Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow. Send a test case, request the price list, or book a factory or video visit.