FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Dentures
Flexible

Valplast Single Tooth Denture Case: Keeping Clasps Off a Thin Gum at #7

This Valplast single tooth denture fills #7 , an upper right lateral incisor, for the months between extraction and the implant crown. The Rx put gum-colored clasp arms across the front of #6 and #8, right on the gum that the one clinical study of this appliance measured.

Final design · single-tooth Valplast · #7
#5
Clasp arm end
#6
Clasp arm
#7
Denture tooth, A2
#8
No clasp · thin gum
One arm, #6 to #5; nothing on the face of #8
Valplast Light Pink base

Single-Tooth Valplast Partial Case at a Glance

Tooth replaced
#7, upper right lateral incisor
Why it’s interim
Implant planned about 4 months after extraction
Appliance
All Valplast, no metal
Base shade
Valplast Light Pink
Clasp arms
One arm, #6 to #5. Nothing on the face of #8
Denture tooth
A2, shaped from the pre-extraction scan
Stages
Design check, wax try-in, final
Shipped
Lab day 7
Later
One lab reline at week 9

Patient Situation

#7 had a root fracture under an old post crown . The dentist took it out and grafted the socket . The plan: implant at about 4 months, crown after that , so the Valplast single tooth denture has to work for roughly 6 months . The patient wanted nothing metal in the smile and didn’t want the front teeth cut for a bridge .

What the dentist’s notes and the models showed:

Gap: 6.4 mm wide. #10, the other lateral, measures 6.6 mm .
#8: natural, no fillings, thin and scalloped gum .
#6: natural canine, thick healthy gum, 0.3 mm of facial undercut.
#5: first premolar, 0.6 mm mesiofacial undercut, shows only from the side .
Bite: 3 mm overbite, 2 mm overjet . #26 touches the #7 space lightly on closing .
Gums: periodontally stable, per the dentist .
Smile: gum margins from #5 to #12 show at full smile .

Records we got: an intraoral scan taken before the extraction, alginate impressions of both arches taken 2 weeks after it, a VPS bite, a shade-tab photo, a full-smile photo, and the Rx form .

What the Dentist Asked For

The Rx, condensed :

Valplast, no metal anywhere.
Clasp arms on the facial of #6 and #8.
Keep pressure off the graft.
Copy the old #7 crown shape from the pre-extraction scan. Shade A2.
As little palate as possible.
Wax try-in before processing.
It has to last until the implant crown, and the ridge will change before then.

Items 2 and 5 pull against each other. Take the arm off #8, and the grip has to come from somewhere else, usually the palate.

The Technical Problems in This Valplast Single Tooth Denture

The arms cover the gum the study measured

Flexible arms look like gum because they run over the gum. On #8, that means a band of resin sitting on the labial margin of thin tissue every day.

There’s exactly one clinical study on this setup. In Zhou and colleagues’ 2011 study, 76 patients who needed a temporary front tooth picked either a Valplast denture or a conventional partial. Another 38 had no temporary at all.

The team measured crown height of the teeth next to the gap on stone models, about 2 weeks after extraction and again at 97–100 days. The Valplast group’s neighbors lost a mean 0.5 mm of gum (range 0.0–1.2 mm). The other two groups: 0.0 mm. The authors judged Valplast unsuitable for a single missing front tooth.

It’s not a strong study. Patients chose their own group, follow-up was about three months, and it doesn’t say how the clasps were designed. But it’s the only one that looks at a Valplast single tooth denture in the front of the mouth, so the dentist needed to see it before deciding where the arms go.

The ridge won't stay put

The impression was taken 2 weeks after extraction, over a fresh graft . That ridge will keep changing for months. A base that fits on day one can leave a gap under #7 by month two, and food goes straight into it. Valplast doesn’t take a quick chairside reline the way acrylic does. Valplast describes rebasing as lab work.

One tooth, held in mechanically

Nylon doesn’t bond to a denture tooth chemically. In a Valplast single tooth denture, the tooth stays in because the resin locks around it. In a one-year study of 120 older adults, the 40 Valplast wearers lost four denture teeth. Those weren’t single-tooth cases, but on this appliance, one loose tooth is the whole job.

What We Sent the Dentist Before Making It

We held the case on lab day 1 and emailed three designs, the study, and the model photo with the gum margins marked.

A: As writtenB: Grip moved off #8C: Arms on both, lifted
Arms#6 and #8 facial#6 running back to #5; #8 held from the palatal side#6 and #8 facial, edge lifted off the gum
Resin on #8’s facial gumYesNoLess, but the arm still crosses it
GripMostLess in front, made up at #5Least: the arms ride high on the teeth
PalateSmallA narrow strap from #5 to #9Small
The catchDaily cover on thin gum, right where the study lookedMore palate, a longer piece, #5 arm shows in side viewA gap at the arm edge catches food, and the top line shows

The dentist picked B and asked us to keep the strap from going past #9 . The #6 arm still crosses #6’s gum, but that gum is thick and doesn’t show as much, and the dentist was fine with it .

We also offered two extras, and the dentist said yes to both :

Baseline numbers. Measure crown heights of #5, #6, and #8 on the 2-week model and write them on the delivery note. That way the dentist can measure the same way at recall, the same method the study used.
A reline plan. Expect one lab reline before the implant. When food starts packing under #7, send the appliance with a fresh alginate impression.

How We Met Each Requirement

Rx itemWhat we didHow we checked
1. No metalBase, strap, and arm injected as one Valplast pieceResin as written on the Rx
2. Arms (changed to design B)One arm, #6 to #5. No resin on #8’s facialDesign photos approved by the dentist
3. Off the graft0.5 mm relief over the socket, light ridge-lap contactChecked on the model before flasking
4. Copy the old #7Tooth shaped from the pre-extraction scan, width matched to the gapOverlay on the scan, then try-in
5. Little palate6 mm strap hugging the cingulums, #5 to #9Try-in, speech check
6. Wax try-inWax setup sent before processingDentist’s photos and notes
7. Lasts to the implantBase kept even so it can be relined; reline plan agreedDelivery note

Holding #8 from the back

On #8, the strap sits on the cingulum, above the palatal gum margin, with a small relief at the margin . It keeps the piece from tipping forward. That’s the job the #8 arm would have done.

The #6 to #5 arm

The arm starts at the gap, runs low across #6, and ends in the #5 mesiofacial undercut . Across #6 it’s 4 mm wide . It widens to 5 mm on #5, where it does most of the gripping . Caliper reading: 1.2 mm thick .

Keeping a Valplast single tooth in the base

We cut a retention groove in the ridge lap of the A2 tooth and cleaned every bit of wax out of it after boil-out . Wax left in a retention area means resin can’t lock in.

The baseline numbers

ToothCrown height at mid-facial, 2-week model
#57.8 mm
#610.1 mm
#810.6 mm

All values in this table are sample data .

What the Wax Try-In Changed

The dentist seated the wax setup, took full-smile photos, and had the patient read aloud .

CheckedWhat it showedWhat we changed
#7 length0.4 mm longer than #10Shortened it
Arm on #6Top edge showed at full smileLowered it 1 mm
Strap edgePatient felt it on “s” soundsThinned and rounded the edge
Lip over #7Even with the other sideNothing
ShadeA2 read right next to #8Nothing

Wax can’t test grip, so that waited for the final. We sent photos of the changes and got the go-ahead .

Making It, Day by Day

Lab dayStage
1Survey and design check
2–3Wax setup, checked on the articulator, out for try-in
4Try-in changes
5Flasking and Valplast injection
6Finishing and polishing, tissue side protected
7Final inspection by our QC team, shipped

The Finished Valplast Single Tooth Denture

Final inspection found:

CheckResult
SeatingFull seat, no rocking, no lifted edges
#8 facialNo resin contact
Arm tipIn the #5 undercut
Grip by hand on the modelFirm, no binding going in
Socket areaRelief present, no contact
Base and strap thickness, caliper2.0–2.4 mm , no sudden changes
Base under strong lightNo bubbles
#7 under finger pressureNo movement
Articulating filmLight mark from #26 on closing, nothing in side moves

Week 9: the reline

At week 8, food started packing under the Valplast single tooth denture, and it came back to us with a new impression . We relined the base and sent it back . The patient went without it for the round trip .

What it doesn't do

It doesn't prove the gum will stay put. Moving the arm off #8 takes away one daily contact. That's all. No study shows that this design makes a difference.
It doesn't take a hard bite on #7.
A Valplast single tooth denture isn't a long-term tooth. A 2025 systematic review found weak evidence that flexible designs perform like conventional partials.

Feedback From the Dentist and Patient

The dentist

Seating

warmed in hot water for 30–60 seconds, the way Valplast describes, and in on the first try .

Grip

firm with no adhesive. One spot on the strap behind #5 needed easing .

Planning

having the designs and the study before anything was made made the talk with the patient easier .

Gum at week 9

the margins on #6 and #8 looked level with the starting photos. The measured check against the baseline numbers comes at the implant visit .

The patient

Speech

noticed the strap when talking for the first few days, then stopped noticing it .

Daily use

in and out without help after a couple of tries in the chair .

Looks

nobody at work has commented on it .

After the reline

food stopped getting under the tooth .

Sending Us a Valplast Single Tooth Denture Case

Send the records first, and we’ll tell you where the arms can go before anything’s made.

Before extraction: a scan or impression, if you have one. It gives us the tooth shape and the starting gum line.
After extraction: alginate of both arches, poured right away, as Valplast asks.
Bite: VPS. Wax softens in transit.
Photos: shade tab next to a natural tooth in the same frame, and a full smile.
On the Rx form: extraction and graft dates, implant timing, "Valplast" written out, where arms may and may not go, how much palate is OK, and whether you want a try-in.

Pack models and impressions the way our how-to-send guide shows. A Valplast single tooth denture generally takes 5–7 working days from the day we receive it, try-in included. Courier and customs time are extra.

Who Made It

Our 55-person removable department made this one in Istar Digital Dental Lab’s own labs. Istar Digital has four labs in Shenzhen and Huizhou, China, about 460 people, and has been doing this since 2012. Nothing gets outsourced. A separate 25-person QC group checks work before it ships. The removable department handles about 4,000 cases a month in the slow season and about 6,500 at peak.

Istar Digital is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA database, and our labs run an ISO 13485 quality management system. For EU clinics, custom-made partials follow the MDR custom-made device procedure.

Valplast Single Tooth Denture FAQ

Can you add a tooth later if a neighbor is lost?

Yes, a Valplast single tooth can take another tooth later. It’s lab work. Send the appliance, models of both arches, and a bite.

Yes, carefully. Valplast’s clinical techniques page describes warming the clasp in hot water, bending it, and letting it cool. Check with us before you grind anything off an arm.

Follow Valplast’s care page: a denture brush, a daily soak, and keep it wet when it’s out. Toothpaste can scratch the surface.

Istar Digital’s warranty on a Valplast single tooth denture is 1 year. A base that won’t seat, lifted edges, badly placed clasps, an off bite, or a gum color you’re not happy with get adjusted or remade free. Changing the shade or material later isn’t covered, and neither is going ahead on a poor impression after we’ve warned you. You pay to send a case in, and we pay to ship finished work back, remakes included.

Valplast’s own limited lifetime warranty is separate. It covers breakage of the resin base, not the teeth.

Yes. We can ship a Valplast Certificate of Authenticity with the case when you need one.

We make it to your Rx, and you don’t need to sign a risk form. Problems caused by that design, remakes included, aren’t on us. If you’d rather change it, we change it.

Yes. Our implant lab makes the restoration on the implant. We don’t make the implant itself.

Yes, free of charge, if you send us 10 or more cases a month. We guarantee the ship date, not the arrival date, because customs times vary.

Prices aren’t on the website. Quotes are itemized to your requirements, not one bundled price.

Send Us Your Next Valplast Single Tooth Case

Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow. You can also book a factory or video visit. Other removable options are on our partial dentures page.