FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Implants
Full arch

Upper Dental Implants Case: A Fixed Bridge for a High Smile

This upper dental implants case came down to one thing we couldn’t see on a model: what happens when the patient really smiles. Six implants were already in. The dentist wanted a fixed zirconia bridge, no flange, and no visible line where the bridge meets the gum .

We didn’t place the upper dental implants. We made what goes on top. And the first PMMA try-in showed the plan wasn’t there yet .

Final design · upper full arch · #3–#14
#4
Implant · 30° MUA
#5
Pontic
#6
Implant
#7
Implant
#8–#9
Pontics
#10
Implant
#11
Implant
#12
Pontic
#13
Implant · 30° MUA
One piece, screw-retained, multilayer zirconia on Ti-bases
Pink gum at the front

Upper Implant Restoration Case at a Glance

Restoration
One-piece, screw-retained upper full arch bridge, #3 to #14
Implants
Six, at #4, #6, #7, #10, #11, and #13 ;
Abutments
Multi-unit: 30° at #4 and #13, straight at the other four
Final material
Multilayer zirconia on Ti-bases, with pink gum at the front ;
Opposing arch
Natural lower teeth, #18 to #31
Implant position records
Photogrammetry, plus intraoral scans
PMMA try-ins
Two
Final stage
Shipped on working day 7

Patient Situation

The patient , in their late 60s , had worn a full upper denture for about six years . The request that started it all: no more denture adhesive . The lower arch still had all its natural teeth back to the second molars .

Three things shaped the whole job on these upper dental implants:

A high smile. At a full smile, the patient showed the teeth and a good stretch of gum above them .
A denture doing two jobs. The old flange was holding the upper lip out, not just holding teeth .
Implants that follow the bone. #4 and #13 tilt back, away from the sinus. #7 leans toward the lip, and that area needed a bone graft at placement .

The surgeon and the dentist made the clinical calls before the upper dental implants case reached us. Six implants was one of them. The ITI consensus found no significant survival difference in the upper jaw between fewer than five implants and five or more. It also asks you to think about what losing an implant later would do to the bridge. That was the dentist’s thinking here .

The graft also ruled out same-week loading. ITI lists simultaneous bone augmentation as a relative contraindication to immediate loading, so the dentist waited five months and kept the patient in the relined denture . Good news for us: that denture became our lip support reference.

What the Dentist Asked For

The Rx came down to six points :

One-piece fixed bridge on six multi-unit abutments, #3 to #14.
No visible line between bridge and gum at a full smile.
Lip support matching the old denture, without a flange.
No screw holes on the facial of any front tooth.
A tissue side the patient can actually clean.
PMMA try-in first, then final zirconia within 7 working days of approval.

Points 2 and 3 are the hard ones on full upper dental implants, and here’s why. An Inside Dental Technology article on choosing an upper implant prosthesis comes down to three parameters: prosthetic space, lip support, and the transition line. A fixed bridge has no flange. So whatever the flange was doing has to come from the shape of the bridge itself.

What We Checked Before Designing

Every set of upper dental implants gets these checks first. Most of it is boring. It’s also where bad cases get caught.

Implant data. We matched system, platform, and scan library against the labels the dentist sent . Same library version for the whole case.
Photogrammetry. We take these files. They gave us the six implant positions, and intraoral scans gave us the tissue and lower arch . A 2025 meta-analysis rated photogrammetry above intraoral scanning for full-arch implant records. We still check across the arch, because no file is proof by itself.
Bite and looks. Scan of the relined denture, VPS bite, face-bow, and photos at rest, in full smile, and in profile . Wax wouldn't have survived the trip.
Space. The dentist measured about 16 mm from ridge to opposing teeth up front and about 13 mm at #4 and #13 . Enough for one-piece zirconia with no bar, so the dentist went that way .

The Problems in This Upper Full Arch Bridge

A screw hole on the front of #7

Our first design preview had the straight channel at #7 coming out on the facial, about 2 mm below the incisal edge . That breaks point 4 of the Rx. The fix had a limit, too: an angled channel can only go as far as the implant maker allows.

We read the offset in the software, then moved the opening to the cingulum with a 20° angled channel, inside that system’s limit . Then we checked the screw path in 3D for interference, and checked the wall around the channel. The dentist approved it before anything got milled .

The first PMMA try-in

We shipped the first milled PMMA on working day 4 . It seated without rocking, and it passed the one-screw test on all six abutments . Midline, bite height, and tooth shape all looked right, and #3 just needed one contact lowered .

Then the patient smiled. Two problems :

The line showed. About 1.5 mm of the transition line was visible from #6 to #11.
The lip looked flat. Next to the old denture, the upper lip dropped in beside the nose.

No model tells you this. You need a face, and you need the prototype in the mouth.

Why you can't just add more pink

On upper dental implants, both fixes pull on the same area. Taking the pink higher hides the line. Thickening it brings the lip out. But do both without thinking, and you’ve got a bulky bridge that traps food, and that breaks point 5.

We use at least 2 mm of cleaning space between bridge and tissue, and we weren’t giving that up.

How We Met Each Requirement

We sent the dentist the marked photos and three options through the case’s WhatsApp group :

OptionWhat it meansThe catch
Reduce the ridgeMoves the line up and out of sightThe dentist’s call; it means removing tissue around new abutments and a graft
Reshape the pinkPink goes higher and fuller, teeth stay putMore bridge to keep clean
Go removableA flange gives the lip backNot what the patient wanted

The same article suggests ridge reduction when the ridge shows, if it’s safe to do, and leans removable when the lip needs a flange. So we said plainly that reshaping the pink might not get there. The dentist looked at the graft and passed on reduction, and the patient didn’t want removable. Test the pink in PMMA first, the dentist said .

So on the second PMMA, we took the pink 1.5 mm higher and made it about 1 mm fuller from #6 to #11 . The tissue side stayed smooth and convex, with no ledges. Teeth didn’t move.

Dentist’s requirementWhat we didHow we checked it
One-piece bridge on six abutmentsOne shared path across all sixNo rocking on the model, no force, no pulling down with screws
No visible line at full smilePink carried 1.5 mm higher, #6 to #11Full-smile photos at the second try-in
Lip support, no flangePink about 1 mm fuller, using the old denture as the referenceSide-by-side photos with the old denture
No facial screw holes20° angled channel at #73D screw path check, then final check with the real screw
Cleanable tissue sideConvex surface, at least 2 mm of cleaning spaceChecked in design, then on the model under magnification
Final within 7 working daysDesign approval, then productionShipped on working day 7

From PMMA to Final Zirconia

The second PMMA went out on working day 3 of that round . The line was gone at a full smile, and the lip matched the old denture . The dentist had the patient wear it for three weeks , and that turned up something no model would’ve shown. Food kept collecting under #11, so the dentist trimmed the tissue side there and sent a new scan .

Here’s what carried over to the zirconia, and what didn’t:

Copied from the approved PMMABuilt new
Bite and bite heightAll implant interfaces, from the implant library
Tooth position and outer shapeThe adjusted inner surfaces of the prototype, which we threw out
Pink height and fullness
Screw channels, including #7
The dentist’s trim at #11, added as its own design change

Then:

Design approval. We sent occlusal, facial, and palatal views, plus connector cross-sections, screw hole positions, and contact points. The dentist approved it the next working day .
Milling and sintering. We kept the thickness even and avoided sudden changes in section. The arch sat on multiple supports in the furnace so it wouldn't sag under its own weight.
Fit check after sintering. We put it back on the model to look for any distortion before going further.
Ti-bases. We bonded them with resin cement, cleaned off excess before it set, and checked under magnification that nothing reached the interfaces .
Pink gum. We matched zones of color to calibrated photos, then compared under more than one light. Photos guide the zones. We don't copy a screen color .
Sign-off. The senior designer reviewed the design, a senior QC inspector reviewed the finished bridge, and the technical lead took a final look at fit, bite, and shape.
Shipped on working day 7 of the final stage .

The Finished Upper Dental Implants Bridge

Here’s how the try-in findings ended up :

CheckFirst PMMASecond PMMAFinal zirconia
Transition line at full smileAbout 1.5 mm showingNot visibleNot visible
Lip beside the noseFlat next to old dentureMatched old dentureMatched second PMMA
Screw hole at #7CingulumCingulumCingulum
FitNo rockingNo rockingNo rocking on the model
Tissue side at #11Not yet testedFood trap, trimmed by dentistTrim carried over

Feedback After Fitting

Dentist

The bridge seated at the first appointment, with screws torqued to the implant maker’s numbers. One light contact at #14 needed adjusting .

Patient

No more adhesive. Using a water flosser daily. No food complaints at the three-month check .

What This Design Still Needs

A fuller pink area on upper dental implants is a trade-off. It’s more surface to clean, so the dentist booked regular hygiene visits with the bridge off . And we won’t oversell the material: a 2023 narrative review of zirconia full-arch work reports 88% to 100% survival, with most complications fixable by the clinician. Those are group numbers, not a promise for this bridge. Three months is a start, not a verdict.

Sending Us Upper Dental Implants Cases

Want a preview that catches this stuff early? Send:

Implant details: system, platform, and connection, with a photo of the labels and your scan library name.
Positions: full-arch scan bodies, photogrammetry, or a verified model. Our digital workflow page covers files, and our how-to-send guide covers physical cases.
Bite and looks: VPS bite, face-bow, the old denture, and photos at rest and in full smile.
Your readings: ridge-to-opposing space and how much gum shows at a full smile.
On the Rx form: final material, how many try-ins, and anything that can't show.

The final stage of an upper full arch bridge takes 5–7 working days. Try-in rounds, clinic visits, and shipping come on top of that.

Who Made It

This upper full arch bridge ran through our implant dental laboratory team of about 80 technicians, and a separate QC team of about 25 inspected it before it shipped.

Istar Digital Dental Lab runs four labs in Shenzhen and Huizhou, China. We’ve been doing this since 2012, we have about 460 people, and nothing gets outsourced. We’re an FDA-registered establishment (Registration Number 3039441248), and you can look us up in the FDA establishment registration database. Our labs run an ISO 13485 quality management system, and custom-made work for EU clinics follows the MDR custom-made device procedure. Want to see it? Visit the factory or book a video tour.

Full Upper Dental Implants FAQ

Do you work with my implant system?

Most likely. We restore upper dental implants from most systems on the market. If your implant library differs from ours, we’ll use yours.

Yes: titanium bars, multi-unit abutments, temporary cylinders, screws, and tools. Parts are charged separately, and their batch and supplier records are traceable.

No. We also make titanium bar with zirconia or resin teeth, titanium bar with PMMA, and PFM. Space and strength usually decide it. For more options, see our All-on-X page.

Yes, along with the final bridge. Tell us your timing early. We’re in China, so shipping has to be part of the plan.

Then a removable design on the upper dental implants may suit better. Here’s an upper implant denture case built around that question.

We’ll tell you why it worries us. Want it changed? We change it. Prefer your design? We’ll build it to your Rx, with no sign-off form. Remakes caused by that design aren’t on us, though.

An upper full arch bridge like this one carries a 3-year warranty. Problems on our side, like a bridge that won’t seat, a high bite, or a color that’s off, get adjusted or remade free. If you change the basic requirements or the material, or ask us to go ahead on records we’ve flagged as unclear, the remake is charged. You pay to send records in, and we pay to ship finished work back, remakes included.

We don’t publish prices on the website. Ask for our price list, and we’ll quote each upper dental implants case item by item, so you can see what the parts and try-ins add. Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow.

Send Us Your Next Upper Case

Got a patient with full upper dental implants, a high smile, and a denture flange doing the lip’s work? Send the case with your smile photos. You’ll see the design, with the tight spots marked, before we make anything.