Patient Situation
Here’s what the dentist’s notes, scans and photos showed before we planned the full mouth zirconia crowns:
The European consensus on severe tooth wear says to manage the cause first and put off restorative work as long as you reasonably can. The dentist had done that. The wear had still gone past what fillings could hold .
Why Every Tooth Got a Crown
The dentist planned to raise the vertical. Every tooth that has to carry new height needs a restoration, and here that meant both second molars in each arch too . Leaving the second molars out would have left them out of contact once the bite went up. That’s what makes this a full mouth zirconia crown case and not a “most of the mouth” one. It’s also what made the records hard.
What the Dentist Asked For
The Rx for the full mouth zirconia crowns, condensed :
The Records Plan
The dentist sent the record plan with the Rx . It was built around one rule for a full mouth zirconia crown case: never take all the provisionals off at once until the bite is captured.
| Record | How it was taken | What it was for |
|---|---|---|
| Provisional scans, both arches, in closure | Before any final prep scans | The approved target: length, shape, guidance, vertical |
| Facebow record | Same visit | Mounting the upper arch |
| Right segment bite | Provisionals off #2–#5 and #28–#31, the rest left in | Lower position on the right |
| Left segment bite | Provisionals off #12–#15 and #18–#21, the rest left in | Lower position on the left |
| Front segment bite | Provisionals off #6–#11 and #22–#27, both back segments in | Lower position at the front |
| Prep scans, both arches | Last, with all provisionals off | Margins and inner surfaces |
| VPS bite for each segment | Taken with each scan bite, sent by courier | Backup check. VPS holds its shape in transit, and wax doesn’t |
Three segment bites that all agree tell you the vertical survived the switch from provisionals to preps. That’s the whole point of taking three.
How We Built the Full Mouth Zirconia Crown Set
Wax-up and provisionals
We mounted the pre-op models on the facebow record and set the pin at +2.0 mm . A full-mouth bite change gets a semi-adjustable articulator and its own settings, not an average one. The digital wax-up for the full mouth zirconia crowns added 1.5 mm of edge length to #8 and #9, 1.0 mm to the lower incisors, and full cusps back on the molars .
We milled the provisionals from the wax-up in PMMA . A systematic review on raising the vertical found no evidence that an evaluation period improves outcomes, and in its one trial, the removable devices caused chewing, speech and looks complaints. Fixed provisionals were this dentist’s choice, and for a zirconia full mouth rehabilitation they gave us a target better than any wax-up .
The patient wore them for ten weeks . Two things changed chairside, and the dentist wrote both on the Rx update :
| What came up | What the dentist changed |
|---|---|
| Patient felt #8 and #9 were a touch long | Took 0.5 mm off both edges |
| #11 caught in left side movements | Smoothed the palatal slope of #11 |
The vertical stayed at +2.0 mm . Both changes showed up in the provisional scan, so we didn’t need anything more than a note telling us to trust the scan over the wax-up.
Checking the bite before any design
With 28 preps in a zirconia full mouth rehabilitation, the bite on the articulator is only as good as the records. So before design, we mounted the lower arch three times, once on each segment bite, and compared where it landed against the provisional reference .
Two out of three matched. The third didn’t :
| Segment bite | Lower arch position vs. the provisional reference |
|---|---|
| Right | Within 0.05 mm at the pin |
| Front | Within 0.05 mm at the pin |
| Left | 0.4 mm open at the pin, shifted slightly to the left |
That 0.4 mm sounds small. But on the left molars it works out to about 0.2–0.3 mm . If we’d designed to that record, the left crowns would have come out high, and the dentist would have been grinding through the occlusal surfaces of eight brand-new crowns to bring them down.
We can’t tell from the files why it happened. A cheek in the way, a patient who didn’t close all the way, or the software matching the bite scan a little off can each do it. A meta-analysis of full-arch intraoral scans found mixed accuracy results, with most falling within clinically acceptable limits. Most isn’t every one, and that’s why a full mouth zirconia case gets three bites checked against each other, not one bite trusted.
Three ways forward
We stopped before designing a single full mouth zirconia crown and sent the dentist the overlays, the pin readings and three options :
| Option | What it does | The catch | Dentist’s call |
|---|---|---|---|
| 1. Wait for the left VPS bite | Mounts the left side from the physical backup | 3–4 more days for the courier, and the VPS might show the same problem | Kept as a cross-check |
| 2. Re-scan the left segment bite | New left record, same method as the others | A short visit, with the left provisionals off again | Yes |
| 3. Drop the left record | Mounts from the right, front and provisional bites only | The left preps never get checked in closure | No |
The dentist re-scanned the left segment the next day . The new scan landed within 0.05 mm of the other two at the pin . When the left VPS bite arrived later, it matched as well . With both left records now in line with the right and front bites, we started design.
Designing the Zirconia Full Mouth Rehabilitation
Copying the provisionals
We lined the prep scans up with the provisional scans and copied the outer shape of each provisional onto its matching full mouth zirconia crown . The prep scans set the margins and inner surfaces. Everything the patient sees, feels with their tongue or bites on came from the provisionals, including the 0.5 mm off #8 and #9 and the smoother slope on #11.
Design approval
The preview of the full mouth zirconia crowns went out with occlusal, facial and lingual views of both arches, the contact map at the new vertical, and the side movements with the back teeth apart . The dentist asked for slightly wider embrasures between the lower premolars for brushing, then approved it in writing .
Discs, color and finish
All 28 full mouth zirconia crowns came from one material lot . Front teeth sat with their incisal thirds in the more translucent part of the disc, and the molars sat lower, where strength matters more than translucency . With 28 crowns in one smile, small color drift shows, so every crown got the same sintering program and shade reference, and a reference piece went through with each batch .
Finish on the full mouth zirconia crowns was split by zone :
Every tooth here bites on another crown, and the patient grinds at night. Glaze on a contact gets ground through at the first chairside adjustment and leaves a rough spot. A polished contact can be adjusted and polished again to the same surface .
There’s no porcelain on any full mouth zirconia crown in this case, by Rx. A systematic review of tooth-supported zirconia, pooling 74 publications, found porcelain-veneered zirconia had more failures and complications than monolithic, mostly chipping.
Final checks
Full-mouth work gets an extra review on top of our three QC stages, and two people sign it off . A QC technician who didn’t make the full mouth zirconia crowns checked:
QC photos went to the dentist before shipping. The crowns shipped 6 working days after design approval .
The Finished Full Mouth Zirconia Crowns
The dentist seated the full mouth zirconia crowns one arch at a time, upper first . Seating order and cement were the dentist’s choice.
What the dentist told us
Notes from the dentist after seating :
What the patient told us
The patient’s comments came through the dentist :
What This Set Can't Promise
We don’t have long-term follow-up on this full mouth zirconia crown set yet . Published reviews look at single crowns and bridges, not a zirconia full mouth rehabilitation of 28 crowns at a new vertical, so we won’t quote you a survival rate for a set like this.
Send Us Your Full Mouth Zirconia Case
Planning a full mouth zirconia crown case? Here’s what helps us most:
- Tell us the plan: a tooth chart, the vertical change at the pin, and how you’ll take the bite once the provisionals come off.
- Rx: use our Rx form. Here’s how to send a case, scans or physical impressions. Digital files go through our digital workflow.
And here’s what you get:
- Lead time: 5–7 working days at the lab for the final crowns of a full mouth zirconia case. Design approval can add 1–2 days, and time waiting on replies or new records isn’t counted.
- Shipping: you pay to send work to us, and we pay to ship finished work back, remakes included.
- Warranty: 3 years on crowns. Open margins, a high bite, a crown that won’t seat, a wrong shade or poor shape all get remade free.
- Quotes: itemized to your Rx, not one bundled price. Ask for the price list.
Full mouth cases go to a dedicated team in our own four labs in Shenzhen and Huizhou, China. We’ve been at it since 2012, with about 460 people, and nothing gets outsourced. At peak we make about 15,000 zirconia single crowns a month.
Istar is an FDA-registered establishment, Registration Number 3039441248, which you can look up in FDA’s establishment database. The lab runs under ISO 13485. You can also book a factory or video visit.
Have a full-mouth bite change coming up? Send it as a test case. Send your first case or talk to us.
FAQ
What if I want a design you've flagged as risky?
That’s your call, and you don’t need to sign anything. We flag it and ask once. If you still want it, we make it to the Rx. Problems from that choice, remakes included, aren’t ours to cover.
Can I get the zirconia brand and batch for the case?
Yes. Ask, and we’ll give you the brand, origin, batch number and certificates for that case. If you want a certain brand, put it on the Rx. We won’t swap a material without your OK.
Can I ask for a particular designer or QC technician?
Yes. If someone on our team has done your earlier cases, you can ask for them again.
Can you rush a full mouth case?
Rush is free for clients sending 10 or more cases a month. We guarantee the ship date. Arrival depends on customs, so we can’t guarantee that part.