FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Dentures
Flexible

Valplast Upper Partial Denture Case: Joining Two Sides Across a High Palate

This Valplast upper partial denture replaces #5 on the right and #12 and #13 on the left . Two gaps, two sides of the arch, and one Rx: all Valplast, one piece, and as little on the palate as possible. The patient also has a high, narrow palate and teaches school all day , so where the connector crossed mattered a lot.

Final design · upper arch · #4–#14
#4
Abutment
#5
Denture tooth
#6
Low clasp
#11
Low clasp
#12–#13
Denture teeth
#14
Abutment
One piece; front of the palate kept clear
All Valplast, no metal

Upper Valplast Partial Case at a Glance

Appliance
One-piece all-Valplast upper partial
Replaces
#5, #12 and #13
Connector
No wider than it has to be; front palate clear
Clasps
#6 and #11 as low as retention allows
Shade
Teeth A2, base Light Pink
Clearance
6.0 mm at #5, 5.6 mm at #12, 5.4 mm at #13

Patient Situation

The patient had worn an acrylic partial for about three years . It had a wide palatal plate and wire clasps on both canines. Two things bothered the patient: “sh” and “s” sounds came out mushy in class, and the wire on #6 showed in every smile . By the time the case reached us, the partial mostly stayed in a case during the workday . Implants had been discussed, and the patient said no .

The dentist’s notes and the records showed:

Abutments: #4, #6, #11, and #14 natural, not mobile, with stable periodontal findings .
Ridges: both spaces over three years old, broad and rounded, no knife edge .
Palate: high and narrow, with raised rugae and no torus .
Clearance: 6.0 mm at #5, 5.6 mm at #12, 5.4 mm at #13 against natural lower teeth .
Bite: 3 mm overbite, no heavy wear, no reported grinding .
Smile: both canines and both premolar areas show at full smile. #14 barely does .
Metal: no allergy on the chart. This was about looks .

What the Dentist Asked For

The Rx for this upper Valplast partial, condensed :

All Valplast, no metal.
One piece. No separate left and right partials.
Keep the front of the palate clear, because of the speech trouble.
Make the connector no wider than it has to be.
No prep on any abutment.
Keep the #6 and #11 clasps as low as retention allows.
Light contact on the replaced teeth when closing, nothing in side movements.
Teeth in A2, base in Light Pink.
Email the design first, then a try-in so the patient can read aloud with it.
Valplast Certificate of Authenticity with the case.

Why This Upper Valplast Partial Took Extra Planning

Room for the teeth wasn’t the worry. A common rule of thumb asks for about 5 mm of clearance so Valplast can hold denture teeth, and this case had that. The trouble was on the palate and in the undercuts.

The connector had two jobs that pull against each other

The strap links the two saddles so they don’t move on their own. Wider helps with that, since the base has no rests and leans on tissue contact. But wider also means more on the palate, and that’s what the patient had just walked away from.

Valplast flexes, so it won’t brace like a metal frame. A university textbook chapter on major connectors gives a width of at least 8 mm for a single palatal strap, but it’s written for cast metal. We didn’t find a published strap width for Valplast. So the width here is a decision for this one case, not a rule.

This palate shape is the hard one for speech

In a small study of 17 people wearing trial connectors, connectors could disturb speech in people with high palates, narrow arches, and small front spaces. The sound that showed it was “shi.” Those people had full natural teeth, so it isn’t a study of partials. It still pointed at this patient’s exact complaint.

Two sides, one path of insertion

A one-sided partial only has to suit one side. This one had to go in on a single path that worked for all four abutments. On a level survey, the left canine came up short:

SpotLevel surveyAfter 2° side tiltShows at full smile?
#6 distobuccal0.9 mm0.7 mmYes
#4 mesiobuccal0.7 mm0.7 mmYes
#11 distobuccal0.4 mm0.6 mmYes
#14 mesiobuccal0.8 mm0.8 mmBarely

The tilt evened out the canines and left the back abutments alone.

The Three Designs We Sent the Dentist

We held the case on lab day 1 and emailed the survey and this table:

OptionWhere it crossesGoodThe catch
A. Front strap, all ValplastOver the rugae, straight from #5 to #12Shortest route between the saddlesSits right where the tongue works for speech. Conflicts with Rx item 3
B. Mid-palate strap, all ValplastJust behind the rugae, 12 mm wide to startFront of the palate stays clearStill crosses the vault, so speech isn’t a sure thing. Flexes, no rests
C. Metal framework partial with rests and a palatal strapThin rigid strapSteadiest. Teeth and ridge share the loadConflicts with Rx items 1 and 5. Metal clasps show unless redesigned

We said Option C would be the steadiest, and the literature agrees. A Japan Prosthodontic Society position paper doesn’t recommend flexible partials with no metal framework as definitive dentures, outside limited cases like metal allergy. And a one-year study of 120 upper partials suggests polyamide for small edentulous areas and light chewing loads. It also found acrylic gave more bulk and speech trouble, which fit this patient’s history.

Two short spaces and no heavy wear sat within that study’s suggestion , and the patient wouldn’t accept a metal clasp . The dentist went over it with the patient and picked Option B for this Valplast upper partial denture . That call belongs to the dentist. The risks were on the table, so we built it to the Rx.

How We Built This Valplast Upper Partial Denture

Here’s how each line of the Rx turned into lab work:

Rx itemWhat we did
1Valplast resin only. Base, strap, and clasps as one piece
2Joined both saddles with the one strap
3Kept the strap’s front edge behind the rugae
4Started at 12 mm, then let the try-in decide
5Used existing undercuts, no prep or rest seats
6Ran the #6 and #11 arms low and checked them against the smile photo
7Set contacts on an articulated model and marked them with film
8Checked teeth and base against the shade photos, before and after finishing
9Emailed design screenshots, waited for sign-off, then sent the try-in
10Recorded the resin details on the certificate

Shaping the strap for a high vault

A strap that bridges a high vault would leave a gap the tongue can find. So we kept it on the tissue all the way over, 1.6–2.0 mm thick , and thinned both long edges so they fade into the palate . We relieved nothing over the midline, since there’s no torus .

Sizing the clasps

The canines show, so they get narrower arms: 4.5 mm wide and 1.2 mm thick , going for the 0.7 and 0.6 mm undercuts. #4 and #14 carry more of the grip at 5 mm wide and 1.4 mm thick . A lab study of thermoplastic clasps recommends 1.0–1.5 mm for a 5 mm wide Valplast arm, so the canine arms are a bit narrower than what it tested.

Keeping the denture teeth in

Valplast holds denture teeth mechanically, with no chemical bond to rely on. So each tooth got retention holes, and we cleared them of wax before injecting so resin could fill them . It’s worth the fuss. Canada’s Drug Agency reports significantly more denture tooth loss on flexible partials at one year in that same 120-patient study.

What the Try-In Changed on the Upper Valplast Partial

The dentist seated the wax try-in and had the patient read a page from a class handout out loud . Notes and photos came back through our WhatsApp group for the case, which has one contact on our side.

A wax base doesn’t flex like Valplast, so this round tested position and bulk, not stiffness.

ItemAt try-inWhat the dentist askedFinal
Strap front edgeTongue caught it on “sh” and “s”Move it back2 mm further back
Strap width12 mmKeep the back edge where it is10 mm
#5 lengthLooked long next to #6 at full smileShorten it0.5 mm shorter
#6 and #11 clasp heightFineNo changeNo change
BiteLight on all three teethNo changeNo change

Narrowing the strap on an upper Valplast partial has a price: less tissue contact and a bit more work for the clasps. The dentist accepted that for clearer speech .

Lab days, start to finish

Day 1 : scans logged, models printed, survey done, options emailed.
Day 2 : dentist's choice in. Teeth set up, design signed off.
Day 3 : teeth set in wax on a trial base, checked, and sent for try-in.
Day 4 : try-in notes applied. Block-out on the tilted path, model duplicated, base waxed up.
Day 5 : flasked, wax removed, Valplast injected into the closed flask.
Day 6 : finished and polished. Outer surfaces only, so the tissue side and fit stay as they were. Then back on the model to recheck the seat.
Day 7 : final inspection, labeled, packed on its own, shipped.

The Finished Valplast Upper Partial Denture

The design goals for this Valplast upper partial denture were one piece, no metal, a clear front palate, and low canine clasps. Final inspection:

CheckResult
Seating on the modelFull seat, no rocking, no lifted edges
Strap width and position10 mm, front edge behind the rugae
Thickness, by caliperStrap 1.6–2.0 mm, saddles 2.0–2.5 mm, no sudden changes
Strap and saddle joins under strong lightNo bubbles or cracks
Teeth, under finger pressureNo movement on #5, #12, or #13
Clasp arms, by caliperWithin 0.1 mm of design
Articulating filmLight, even marks on all three teeth, none in side movements
Smile photo#6 and #11 arms stay low at full smile

Patient and dentist feedback

The dentist: warmed it in hot tap water for 30–60 seconds, as Valplast’s clinical techniques describe, and it seated with firm retention . One spot on the flange at #13 needed easing. The clasps needed nothing .

The patient: a slight lisp on day one, and “sh” sounded normal to the patient and dentist by the two-week check . The partial now stays in during class . The canine clasps can be seen up close but don’t catch the eye . There’s some movement on harder foods , as the dentist had warned.

That’s feedback from delivery and two weeks, not years , so we won’t promise how long this upper Valplast partial will last. Canada’s Drug Agency also says follow-up on flexible partials is too short to judge durability.

The dentist set recall visits for the abutments, ridge, and fit . That’s sensible: redness around abutments showed up with both polyamide and acrylic in the one-year study, and a polyamide literature review also recommends close follow-up.

Sending a Similar Valplast Upper Partial Denture Case

Got a bilateral upper case and not sure about the connector? Send the records first. We offer a pre-shipment feasibility review, and a design is much easier to change before anything’s made.

We need:

Scans: both arches and a bite through our digital workflow. 3Shape TRIOS, Medit, iTero, CEREC, Shining3D Aoralscan, and Planmeca all work.
Or physical records: models or impressions of both arches with a VPS bite, packed per our how-to-send guide. Please skip wax bites, they soften and distort in transit.
Photos: shade tab next to a neighboring tooth in the same frame, plus a full smile.
On the Rx form: teeth to replace, "Valplast" written out, how much palate the patient will accept, any speech or gag history, and whether you want a try-in.

A Valplast upper partial denture generally takes 5–7 working days, and a try-in round counts inside that. Design sign-off can add 1–2 days, and courier and customs time are separate.

Who Made It

Our 55-person removable department made this upper Valplast partial in Istar Dental Lab’s own labs. Istar has four labs in Shenzhen and Huizhou, China, about 460 people, and has been at it since 2012. Nothing gets outsourced. A separate 25-person QC group checks work before it ships, and the removable department handles about 4,000 cases a month in the slow season and about 6,500 at peak.

Istar is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA database, and our labs run an ISO 13485 quality management system. For EU clinics, custom-made partials follow the MDR custom-made device procedure.

Upper Valplast Partial FAQ

Can you reline, repair, or add a tooth later?

Yes, all three, and it’s lab work. Send the appliance, upper and lower models, and a bite record. Valplast’s clinical techniques page covers the impression steps, and its FAQ warns the patient may go a few days without the partial.

We make it to your Rx, and you don’t need to sign a risk form. Problems caused by that design, remakes included, aren’t on us. If you change your mind before production, we change the design.

Istar’s warranty on the base of an upper Valplast partial is 1 year. A base that won’t seat, lifted edges, badly placed clasps, an off bite, or the wrong gum color get adjusted or remade free. Changing the shade or material later isn’t covered, and neither is going ahead on a poor impression after we’ve warned you. You pay to send a case in, and we pay to ship finished work back, remakes included.

Valplast’s own limited lifetime warranty is separate. It covers breakage of the resin base, not the teeth.

Yes. We can ship a Valplast Certificate of Authenticity with the case when you need one, and each certificate has a serial number you can register with Valplast.

A payer’s clinical criteria list D5225 for a maxillary flexible-base partial and D5227 for the immediate version. Coding is the clinic’s call, so check the current ADA CDT Code and the patient’s plan.

Acrylic, cast frameworks, and other flexible partials. The full range is on our partial dentures page.

Yes, free of charge, if you send us 10 or more cases a month. We guarantee the ship date, not the arrival date, because customs times vary.

Prices aren’t on the website. Quotes are itemized to your requirements, not one bundled price.

Send Us Your Next Upper Partial Case

Got a patient who needs a Valplast upper partial denture with both sides joined and as little palate as possible? Single trial cases are welcome, and ongoing partnerships suit clinics with a regular case flow. Ship us a test case, request the price list, or book a factory or video visit.