Patient Situation
The patient, in their 40s, broke the tip off #11 years ago . It got a root canal and a composite build-up with a flat incisal edge, and it stayed that way . It looked fine at rest. But it didn’t do anything in a left lateral move.
Here’s what the dentist’s notes and the scans showed :
That chipping makes sense once the tooth is guiding again, since all the lateral contact now sits on a small area. It’s also a fair concern on material alone. One in vitro comparison of three provisional materials measured bis-acryl lowest for flexural strength after storage. That’s bench data, not a verdict on any one temporary, but it was enough for the dentist to send this one to a lab.
What the Dentist Asked For
The Rx, condensed :
The Technical Problems in This Temporary Canine Tooth
Not enough room on the guiding slope
This was the big one. We loaded the prep scan with the bite and checked the space on the lingual slope, right where #22 would ride during a lateral move. It came to 0.8 mm . Our design target for that spot on this crown was 1.2 mm .
That’s the thinnest part of the crown, sitting under the highest load. And the last temporary had chipped right next to it, at the tip.
A steep slope and a thin feel don't go together
The easy way to get thickness is to build the lingual out. But that makes the slope steeper, which breaks the #6 limit on the Rx. It also fills the lingual concavity, and that’s exactly what feels thick on the tongue.
Mirroring #6 wasn't quite enough
Mirroring #6 gave us a good start for length and tip position. But #11 sits 0.4 mm further facial in the arch than #6 does . A straight mirror would’ve looked bulky at the neck, and with this smile, you’d see it.
Canine guidance wasn't a given
We didn’t just assume canine guidance was the right scheme. A clinical study of lateral contacts found group function more often than canine protection, and most patterns didn’t fit either label. So that’s the dentist’s call, per patient. Here the dentist made it, and the Rx spelled it out, so we designed to the Rx.
Three Ways to Fix the Slope
We posted the clearance map in the case’s WhatsApp group with three options :
| Option | What it means | The trade-off |
|---|---|---|
| A. Keep the prep, mill it thin | 0.8 mm on the slope | Fastest, but the most likely to chip, and it’s the same problem as before |
| B. Keep the prep, build the slope out | 1.2 mm, by moving the lingual surface | Steeper than #6, breaks the Rx, thicker on the tongue |
| C. Take 0.4 mm more off the lingual slope | 1.2 mm with the slope where it should be | One more chair step and a new scan |
We recommended C. How much tooth to cut isn’t our decision though, so the call was the dentist’s. Most of that slope was composite core anyway, and the dentist went with C . The new prep scan came in 2 working days later . Lead time counts from complete records, so our clock started on that scan.
How We Met the Rx: Building the Provisional Canine Crown
Design
Our designer built the form from three sources, each for one job :
| Source | What we took from it |
|---|---|
| #6, mirrored | Length, tip position, the limit for the guidance slope |
| Pre-op scan of #11 | Neck width and emergence, so the facial stayed 0.4 mm in from the straight mirror |
| Left and right lateral bites | The path #22 actually travels, for setting the slope |
Then the numbers went in :
The dentist got the preview and approved it on working day 2 , with no changes.
Material and milling
We milled it from an Ivoclar PMMA disc in A2 . We stock PMMA from Ivoclar and Aidite. For this provisional canine crown, milling was the easy pick over printing, because of 6–8 weeks of guiding load on a thin slope. A review of 19 studies on CAD/CAM interim restorations came out in favor of milled for fit, strength and color stability. 18 of those 19 were lab studies though, so it’s a reason to choose it, not a promise.
Shade and finish
The dentist sent the natural tooth and the stump in the same frame as a VITA classical shade tab . Those stump photos matter here: the composite core was darker than the dentin, and we’d need that later for the final.
The technician stained the cervical third warmer to match #6, then polished the facial to a high shine. A temporary canine tooth in a high smile has to hold its shade for the whole wear period, and a rough surface picks up stain faster.
Checks before shipping
QC checked this provisional canine crown against the Rx and the approved design: margins, the inside surface, the seat, contacts, the bite in centric, protrusion and lateral moves, form, polish, and no cracks or voids. It shipped on working day 6 in a foam-filled box, with the tracking number sent that day .
Seating and the 7-Week Test (the Dentist's Report)
This is where the temporary canine tooth earned its keep. The dentist seated it with a eugenol-free temp cement and reported back with two changes:
Nothing else changed over the 7 weeks . No chips. It never came loose. By the week 1 check, the patient said they’d stopped noticing it on the tongue .
The Finished Temporary Canine Tooth: Targets and Results
Here’s how the provisional canine crown measured up against the design targets :
From the Provisional Canine Crown to the Final Crown
The temporary canine tooth gave us the numbers we didn’t have at the start. At week 7, the dentist sent a scan of the adjusted temporary in the mouth, then a scan of the prep with it off . We laid one over the other. Recording guidance from a provisional the patient has already worn is an established prosthodontic technique, and here we did it digitally.
| Temporary as milled | Final crown | |
|---|---|---|
| Material | Milled PMMA | IPS e.max Press, pressed |
| Guiding slope | Set at the #6 limit | Copied from the temporary after the 0.2 mm adjustment |
| Tip length | Mirrored from #6 | Copied from the temporary after the 0.3 mm trim |
| Facial and neck | From the design | Copied from the scan of the temporary |
| Shade | A2 body, warmer neck | Same target, with the stump shade from the earlier photos factored in |
The dentist approved the overlay, and the final shipped on working day 6 . It seated with one small contact adjustment . Nobody had to guess at the slope or the length, because the patient had already tried both for 7 weeks.
Sending a Similar Temporary Canine Tooth
Got a temporary crown on canine tooth #6, #11, #22 or #27 that needs to do more than hold the space? Here’s how it works with us:
Every step happens in our own labs, with no outsourcing: four of them in Shenzhen and Huizhou, China, running since 2012, with about 460 people, including 100 in design, 70 in milling and 25 in QC. You can book a factory visit or a video visit with sales.
Istar is an FDA-registered establishment, Registration Number 3039441248, which you can check in FDA’s establishment database. The lab runs under ISO 13485, and everything is made to the dentist’s Rx. For EU clients, custom-made devices follow the MDR custom-made device procedure.
Got a temporary canine tooth you’d like to test before going final? Send us the scans and the Rx as a trial case, and we’ll check the clearance on the guiding slope before anything gets milled. Single trial cases are welcome. Send your first case or talk to us.
FAQ
What's the warranty on a temporary canine tooth?
1 year. It’s made for short-term wear, so it doesn’t get the 3 years we give final crowns. Lab-side problems like open margins, open contacts, a high bite, a crown that won’t seat or the wrong shade get remade free. Changing the shade or material later isn’t free, and neither is a remake after you asked us to go ahead on an unclear impression.
Does a temporary canine tooth have to be milled PMMA?
No. We make temporaries in composite resin or PMMA, and we can 3D print them too. We won’t swap a material without your OK.
Can you copy a temporary I made at the chair?
Yes. Scan it in the mouth and send that with the prep scan. We can copy both its form and its guidance.
Do you make temporaries on implants?
Yes. We can also supply temporary cylinders, screws and tools, at extra cost.
Can I use a wax bite with physical impressions?
Please don’t. Wax softens and distorts in transit. Use a VPS bite registration, and VPS is our first choice for the impression too.
Do you take rush cases?
Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t promise that.
How do you price a temporary canine tooth?
Quotes are itemized to your Rx, not one bundled price. Ask us for the price list.