The Patient Behind These Six Veneers
The patient is an adult in their 40s . About 15 years ago, at their own request, another dentist rounded off both canine tips because they looked “too sharp” . Now they wanted the points back. The canines looked short and blunt, and the whole front row read flat.
What the dentist recorded :
The bite : about 3 mm of overbite and 2.5 mm of overjet. No wear facets beyond the old rounded tips, and no clenching or grinding reported. The dentist checked that first, since the ADA says veneers may not be a good choice for people who clench or grind.
Then there’s the side movement. With the canine tips rounded down, the canines and both premolars touched together all the way through each side movement. That’s group function, and the patient had been chewing that way for 15 years without trouble .
What the Dentist Asked For
From the Rx form and our WhatsApp thread :
Along with the Rx, the dentist sent full-arch scans of both arches, a closed bite scan, a protrusive scan, and a bite scan on each side with the canines tip to tip . Those side scans turned out to matter most.
Why the Canines Are the Hard Part of 6 Veneers
In a set of 6 veneers, the centrals and laterals mostly change what you see. The canines can also change how the jaw moves sideways.
The lower canine slides along the back of the upper canine during a side movement. Make the upper tip longer, and the lower canine has further to travel before it clears. On a lot of patients, that’s fine. But on someone in group function, every bit of extra canine height lifts the premolars apart. The bite in the closed position doesn’t move at all. The side movement does.
Our Side-Movement Check on the 6 Veneers Wax-Up
Our CAD team built the wax-up to the Rx first: canine tips 1.0 mm longer, centrals and laterals at today’s length . Then we ran the design for the six veneers against the side scans (aligned in the CAD virtual articulator) and measured the gap at each premolar at two points: 1 mm into the side movement, and with the canines tip to tip.
| Premolar gap (mm) | #5 | #4 | #12 | #13 |
|---|---|---|---|---|
| Today, 1 mm into the movement | 0.0 | 0.0 | 0.0 | 0.0 |
| Today, canines tip to tip | 0.0 | 0.0 | 0.0 | 0.0 |
| Wax-up, 1 mm into the movement | 0.3 | 0.4 | 0.3 | 0.4 |
| Wax-up, canines tip to tip | 0.5 | 0.6 | 0.4 | 0.6 |
A gap of 0.0 means the premolar still touches.
So the six veneers wax-up would have turned group function into canine guidance on both sides. That’s a change to the bite, which item 5 said not to make. And it’d put every side load on two new ceramic tips.
That second part matters for the ceramic. A critical review of incisal prep designs for ceramic veneers found the incisal ceramic is the most common fracture site in clinical studies. The new canine tips would be exactly that: incisal ceramic, now doing all the guiding.
Three Options We Sent the Dentist
We sent the measurements and three options over WhatsApp, each with a screenshot :
| Option | Canine tips | Side movement | Cost |
|---|---|---|---|
| A. Build to the wax-up | +1.0 mm | Canines guide alone, premolars lift off | Changes the bite scheme. All side load goes on the new ceramic tips |
| B. Shorter tips on today’s path | +0.5 mm | Premolars keep touching through most of the movement | Points look less sharp than the wax-up |
| C. Keep today’s canine length | No change | Same as today | Canines stay blunt, which is why the patient came in |
Option A isn’t wrong. Veneered canines can guide well for years. A six-year follow-up of DSD-guided lithium disilicate veneers reported stable canine guidance at recall. But switching a patient’s scheme is a clinical call, and this Rx said to keep the bite.
Which way the jaw moves sideways is the dentist’s decision, not ours. Our job was to show what each option does to the premolars and to the ceramic.
The dentist chose B, and wanted the patient to see and feel it before any tooth was prepped for the six veneers .
Testing Option B in a Printed Mock-Up
We redesigned the canines for option B: tips 0.5 mm longer, with the back of each new tip following the path the lower canine already takes . Then we printed a model of the design and made a silicone index from it, so the dentist could run a bis-acryl mock-up straight onto the unprepped teeth .
At the mock-up visit :
The dentist scanned the adjusted mock-up and sent it in. We copied it into the design, so the final #11 tip is 0.3 mm longer than today and #6 is 0.5 mm longer . The two canines don’t match exactly, and that’s fine. Natural canines rarely do.
The Approved Design and the Prep
The dentist approved the revised design in writing, and the approved contours went on file . For the prep, we sent a sectioned silicone reduction guide cut from the approved design .
The dentist prepped all six teeth for the 6 veneers with a butt-joint incisal reduction, as the Rx asked . When the prep scan came in, we checked the room at each third of every tooth against the design before pressing (CAD wall-thickness map: at least 0.3 mm cervical, 0.5–0.7 mm mid-facial). All six had the planned room. The dentist reported enamel all round, apart from a small dentin spot where the old composite on #9 came off .
Staying in enamel was worth the effort. A meta-analysis of ceramic veneers on different bonding substrates found success dropping as dentin exposure went up, with enamel doing best.
Making the Six Veneers
Shade over the prepped teeth
The dentist sent stump photos with a shade tab in the same plane. The prepped teeth read about A3, even across all six . Six veneers this thin let the tooth underneath show through, so we planned the ingot from the stump shade, not from the target tab alone (IPS e.max Press LT). The premolars #5 and #12 were the color reference.
The canine tips
In production
Design approval took 1 working day, and the mock-up round about a week on the clinic’s side . From the prep scan to shipping took 6 working days .
Finished 6 Veneers: Try-In Results
The dentist tried in all six veneers with try-in paste, then bonded them with resin cement at the same visit, following Ivoclar’s instructions .
| Design goal | How it was checked | Result at try-in |
|---|---|---|
| Group function kept | Articulating paper in both side movements | Premolars marked through most of each movement, canines took over just before the tips crossed. Same as the mock-up |
| No catch on #11 | Left side movement, patient feedback | No catch, no adjustment |
| Closed bite and protrusive unchanged | Articulating paper, against the pre-op bite scan | Marks in the same spots as before |
| Pointed canines | Mock-up scan against the finished veneers | Tips match the approved mock-up on both sides |
| A2 with the premolars | Photos with a shade tab, smile video | No visible step between #6 and #5, or #11 and #12 |
| Clean margins | Dentist’s check at bonding | No ledge at any margin |
Feedback from the Dentist and Patient
The dentist
The side numbers made it easy to talk the patient through 6 veneers that touch the bite. Nobody had to guess what longer canines would do .
Check both side movements at each visit, and watch for the canines starting to guide alone .
The patient
“My canines look like canines again” .
Chewing feels the way it did before .
What to Send for a 6 Veneers Case That Changes the Canines
Here’s how to send a case. Six veneers generally take 5–7 working days, simple cases 2–3, plus 1–2 days when you ask to approve the design first.
Who Made These Six Veneers
These six veneers went through our CAD design team (about 100 people), our ceramic and metal department (about 70) and a separate QC team of about 25. They’re part of Istar Dental Lab’s four labs in Shenzhen and Huizhou, China. We’ve been running since 2012, with about 460 staff and no outsourcing.
Istar Dental Lab is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA establishment registration database. Our labs run an ISO 13485 quality management system.
Six Veneers FAQ
What if my patient grinds?
Tell us on the Rx. For heavy bite forces, we’d talk through zirconia veneers, which are stronger and wear better than glass ceramic. We also make night guards to your prescription.
What if I want a design you think is risky?
We’ll tell you why, then make it to your Rx with no sign-off form. A remake caused by that design isn’t on us, though.
Can you add premolar veneers to a set of 6 veneers later?
We keep the design files and contours of every multi-unit case on record, so later units can follow the same shapes. For color, send fresh shade photos. A new pressing won’t copy an old one just because the shade code is the same.
What else do you make veneers in?
Besides pressed e.max veneers, we make zirconia veneers and lab-made composite veneers. See what else our e.max lab makes. We won’t swap a material without your OK.
What's free to redo, and what isn't?
Open margins, open contacts, high bite, a veneer that won’t seat, inaccurate color, visible flaws and poor shape are ours to fix for free. Changing the shade or material afterward isn’t free. Neither is a case you asked us to make from an impression or scan we’d already flagged as poor.
What about warranty and shipping?
Veneers carry our 3-year warranty. You pay to send a case in, and we pay to ship finished work back, remakes included.
Can you rush a veneer case?
Rush service is free for clients who send us 10 or more cases a month. We guarantee the ship date, but not the arrival date, because customs times vary.
How is pricing handled?
We don’t publish prices on the website. Ask for our price list, and we’ll quote each case item by item to your requirements.
Send Us Your Next 6 Veneers Case
Got a patient who wants their canines back, or any six-unit front case? Single trial cases are welcome, and you can see our labs on a factory visit or a video tour.