FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Crowns & Bridges
Provisionals

Temporary Crowns for Molars Case: Holding the Bite on a Cracked Tooth for 9 Weeks

These temporary crowns for molars went on the upper left first and second molars, #14 and #15 (FDI 26 and 27). They’re two separate milled PMMA crowns, and they had to last 9 weeks , a lot longer than a temporary usually stays in.

That long wait was the whole point. #14 had a cracked cusp, and the dentist wanted to watch it in a temporary before committing to a final crown. So these temporary crowns for molars had two jobs that pull against each other: keep the bite where it was, and keep load off a tooth that was sore when the patient chewed.

Final design · two single temporaries · #14–#15
#13
Adjacent
#14
Milled PMMA · cracked tooth
#15
Milled PMMA
#16
Missing
Not joined; floss passes between
Shade A3

Molar Temporary Crowns Case at a Glance

Restoration
Two separate milled PMMA temporary crowns, #14 and #15
Wear time
8–10 weeks
Shape
Copied from the pre-op scans
Shade
A3
Opposing
#18 and #19 natural; #17 missing
Finals
Monolithic zirconia, copied from the temporaries

Patient Situation

The patient is in their 50s and clenches during the day. There are flat wear facets on the molars on both sides, but no grinding diagnosis and no night guard .

Here’s what the dentist’s notes and the scans showed :

#14 had a crack. It ran under an old MOD composite into the mesiopalatal cusp. Biting on something hard hurt, mostly on release. The tooth still responded to cold, and there was no root canal.
#15 had a big old amalgam with crack lines. No symptoms, but the dentist didn't want to leave it.
#15 is the last tooth in the upper arch. #16 is missing, so there's no tooth behind it.
Down below, #18 and #19 are natural. #17 is missing, so #18 is the last lower tooth, and it sits under #15.

The plan was to crown both. But #14 came first: if its symptoms settled in a temporary, it would go to a final crown. If they didn’t, the plan would change, and that’s a clinical call. Either way, the dentist needed 8–10 weeks of watching .

Why These Molar Temporary Crowns Came to a Lab

The dentist made bis-acryl temporaries at the chair on prep day . That was fine for a couple of weeks. For 8–10 weeks on a clencher, the dentist wanted milled PMMA.

There’s some data behind that. A within-patient study of 22 people needing provisionals on premolars and molars with root canals measured the best fracture resistance and margins on milled PMMA, against self-cure PMMA and printed resin. It was short term, and those teeth had root canals, unlike #14. Still, it’s the closest match we’ve got for a molar temporary crown that has to last.

The other reason was the finals. The dentist wanted whatever the molar temporary crowns proved to go straight into the zirconia crowns. A milled design is a file, so we could copy it.

What the Dentist Asked For

The Rx, condensed :

Two separate milled PMMA temporary crowns, #14 and #15, for 8–10 weeks.
Don't join them. The dentist wanted to take #14 off on its own for checks, and wanted floss to go through.
Copy the pre-op shape of both teeth. The patient was used to it.
Full bite contact on both, "so nothing moves."
Normal contacts with #13 and between #14 and #15.
Shade A3.
Show the design before milling.
Later, make the finals in monolithic zirconia and copy what works from the temporaries.

Item 4 made sense. #15 and #18 are both last teeth in their arches, and a 9-week gap is long. But it’s also where the trouble started.

What We Found When We Lined Up the Scans

We loaded the prep, pre-op, opposing and bite scans together, then ran the left and right lateral bites through the virtual articulator. Four things came up.

The thinnest spot sat under the heaviest load

With the pre-op shape copied at full contact, we measured PMMA thickness across both crowns :

SpotThickness at full contact
#14 mesiopalatal cusp1.1 mm
#14 distopalatal cusp1.2 mm
#15 mesiopalatal cusp1.0 mm
#15 distopalatal cusp0.6 mm
Central fossae, both teeth1.4–1.8 mm

For posterior work, we generally design in a 0.8–2.0 mm range, depending on material. On this case we set 1.0 mm as the minimum , since the crowns had 9 weeks of clenching ahead. #15’s distopalatal cusp didn’t make it.

The pre-op shape had a side-swing contact

In a right lateral move, the patient’s left side is the non-working side. The pre-op scans showed #15’s distopalatal cusp touching #18 during that move . That’s the same 0.6 mm spot. Copy the old shape, and you put a side load on the thinnest bit of PMMA in either crown.

The biggest contact on #14 was on the cracked cusp

The pre-op bite showed the largest contact on the whole quadrant on #14’s mesiopalatal cusp . That’s the cusp with the crack. “Copy the pre-op shape” plus “full contact” meant putting that load right back where the tooth hurt.

Nothing sits behind #15

With no #16, #15 has no tooth behind it, and the same goes for #18 below. If either molar temporary crown came out of contact, nothing else would hold those two teeth.

Two Questions for the Dentist

We posted the thickness and contact maps in the case’s WhatsApp group with two separate questions .

Question 1: the 0.6 mm cusp on #15

We can’t make that spot thicker without raising the cusp, and raising it would open the bite. So we asked whether the dentist could take about 0.4 mm more off #15’s distopalatal cusp and rescan #15. #15 wasn’t the tooth being watched, and it was only one cusp.

The dentist said yes. The patient came back 2 working days later, and the new #15 scan came in that day . Our lead time counts from complete records, so the clock started on that scan.

Question 2: how much bite each molar temporary crown should carry

This one had no easy answer. Here’s what we sent :

OptionWhat it meansThe trade-off
A. As writtenFull contact on both, pre-op side-swing contacts keptHolds everything, but the heaviest contact goes back on #14’s cracked cusp
B. Stops on both, lighter on #14, no side-swing contactsEach tooth keeps contacts that hold it in place. #14’s are set a touch lightLess load on #14, but the patient will feel #14 as “low” at first. Needs a check at seating
C. #14 out of contact, #15 normalAll bite load comes off #14Nothing holds #14 or #19 up and down for 9 weeks, and the patient chews on #15 alone on that side
D. Both out of contactThe least load on either temporaryNothing holds #15 or #18, and the final records may not match the bite from prep day

We told the dentist we’d lean toward B. The evidence doesn’t settle it, though, and we said so.

A randomized study of 50 prepared teeth found that placing a temporary cut tooth movement between visits in upper molars (p = 0.002). That’s an argument for having a temporary at all. It tested overlay preps, published no movement values, and didn’t compare contact schemes.

On the other side, a study of unreplaced back teeth followed for a median of 6.9 years found most patients lost 1 mm of space or less, and the opposing tooth came down 1 mm or less in 99% of cases. Movement happens, but over years. Neither paper picks A, B, C or D for you.

The dentist chose B . Which tooth carries how much bite is a clinical call, and so was the choice.

How We Built Each Molar Temporary Crown

Design

We started from the pre-op scan and only changed what the dentist’s choice required :

FeatureWhat we did
Outer shape, cusp heights, cheek-side profileCopied from the pre-op scan
Centric stops on #15Normal contact on the marginal ridges, the central fossa and the palatal cusp tips
Centric stops on #14The same contact areas, set 0.05 mm short of full contact
#14 mesiopalatal cusp (the cracked one)Kept its shape, with the lightest contact of any spot on #14
Side-swing contactsNone on either crown. #15’s distopalatal inner slope came down 0.2 mm to clear #18 in a right lateral move
Left lateral moveThe natural canine, #11, does the guiding. #14 and #15 clear by 1 mm of movement
ContactsNormal with #13 and between the two crowns. Nothing behind #15
Minimum PMMA1.0 mm everywhere after #15’s new prep, including the trimmed slope

That last row needed a check. #15’s distopalatal cusp came to 1.0 mm at the tip after the new prep, and 1.2 mm on the inner slope . Taking 0.2 mm off that slope left it at 1.0 mm, right on the minimum.

The dentist got the thickness map and the contact map in the preview, and approved them the same day .

Milling and finishing

We milled both molar temporary crowns from a PMMA disc in A3 . We stock PMMA from Ivoclar and Aidite. The technician polished the occlusal and side walls to a high shine.

That polish isn’t just for looks. A split-mouth study of 20 adults who needed molar crowns counted fewer S. mutans on milled PMMA temporaries than on conventional PMMA at one and three weeks. It measured bacteria counts, not gum disease, but 9 weeks is a long time to wear a rough surface.

Checks before shipping

QC checked both crowns against the Rx and the approved design: margins, the inside surface, the seat, contacts, the bite in centric, protrusion and side moves, shape, polish, and no cracks or voids. They shipped on working day 5 in a foam-filled box, with the tracking number sent that day .

Wearing the Temporary Crowns for Molars: 9 Weeks

The weeks below count from the day the lab temporaries went in, about 2 weeks after prep . Before that, the patient wore the chairside ones.

That adds up to about 11 weeks in temporaries. The dentist planned it that way, and it’s worth planning. A retrospective study of 15,879 restorations linked a longer time in an interim restoration with a higher risk of the tooth losing vitality (p < 0.001). That’s a link, not proof of cause, but it’s why a long wait should have a reason and an end date.

What the dentist reported :

Seating: the dentist used a eugenol-free temporary cement. #15's mesial marginal ridge stop marked a bit heavy, so the dentist took about 0.1 mm off it. #14's stops marked light, as designed.
Week 1: the patient said #14 felt "a bit low" when chewing. By week 2 they'd stopped noticing.
Weeks 3–5: #14 still hurt a little on release from hard foods at week 3. By week 5, it didn't.
Week 7: #15 came off once while the patient was eating something chewy. It came off in one piece, and the dentist cemented it back the same day. We don't know why it let go, and the dentist didn't ask for a remake.
Week 8: #14 still responded normally to cold. The dentist decided it could go to a final crown without a root canal.
Week 9: final records. No fractures or chips on either crown in the 9 weeks.

Did the Bite Hold? Checking at Week 9

This is where option B either held up or didn’t. Before taking the temporaries off, the dentist scanned the bite with them still in place . We laid that scan over the bite scan from prep day, lined up on the upper teeth from #13 forward.

At the cusp tips of #18 and #19, we couldn’t see a change bigger than 0.1 mm . The left lateral move was still on the canine.

That’s one patient over 9 weeks. We can’t say option B is why nothing moved, and with drift that slow, it might not have moved under C or D either. What we can say is the final crowns went onto the same bite the case started with.

The Finished Temporary Crowns for Molars: Targets and Results

Design target
Result
At least 1.0 mm of PMMA everywhere
Met after #15's extra reduction
Centric stops on both teeth, #14 set light
Met. One stop on #15 adjusted about 0.1 mm at seating
No side-swing contact on #14 or #15
Met in the articulator, confirmed by the dentist in the mouth
Canine guidance on the left kept
Met
Separate crowns that floss and come off one at a time
Met. #14 came off alone for checks
Intact for 8–10 weeks
9 weeks, no fractures or chips. #15 came off once and was cemented back
Bite at week 9 the same as on prep day
No change over 0.1 mm at #18 and #19

From the Temporaries to the Final Zirconia Crowns

With #14’s watch over, the dentist took the temporaries off and scanned the preps . We built the finals in monolithic zirconia, on the same prep as the temporaries.

TemporariesFinal crowns
MaterialMilled PMMAMonolithic zirconia
Outer shape and cheek-side profileFrom the pre-op scanCopied from the temporaries’ design
Stops on #15Normal contactSame layout, normal contact
Stops on #140.05 mm lightSame layout, back to full contact at the dentist’s request
Side-swing contactsNoneNone, copied from the temporaries
#15 distopalatal slopeTrimmed 0.2 mmSame trimmed slope

Both finals shipped on working day 6 . The dentist touched up one contact on #14 at seating and nothing else . Nobody had to guess where the stops should go, because the patient had already chewed on the molar temporary crowns for 9 weeks.

Sending Temporary Crowns for Molars Like These

Got temporary crowns for molars that have to last more than a couple of weeks? Here’s how it works with us:

Lead time: 5–7 working days at the lab. Asking to see the design adds 1–2 days. Time spent waiting on a rescan or a reply doesn't count, and the clock starts from complete records. Shipping from China comes on top, so plan the chairside temporaries to cover it.
Records: intraoral scans in STL, or physical impressions. Use our Rx form and see how to send a case. We usually check scan files within 1 working day and tell you if anything needs a rescan.
For molar temporaries, add: the opposing arch, a bite, left and right lateral bites, and a pre-op scan if you want the old shape copied.
Write it on the Rx: how long they'll be worn, how much bite each tooth should carry, joined or separate, any clenching or grinding, and whether the finals will copy the temporaries.
References are welcome: a chairside temporary, an old crown, a wax-up or photos.
Shipping: you pay to send impressions or models to us, and we pay to send the finished work back.

Every step happens in our own labs, with no outsourcing: four of them in Shenzhen and Huizhou, China, running since 2012, with about 460 people, including 100 in design, 70 in milling and 25 in QC. Our full crown and bridge work runs through the same lines. You can book a factory visit or a video visit with sales.

Istar is an FDA-registered establishment, Registration Number 3039441248, which you can check in FDA’s establishment database. The lab runs under ISO 13485, and everything is made to the dentist’s Rx. For EU clients, custom-made devices follow the MDR custom-made device procedure.

Got a molar temporary crown that has to hold for weeks? Send us the scans and the Rx as a trial case, and you can see the design before anything gets milled. Single trial cases are welcome. Send your first case or talk to us.

FAQ

What's the warranty on a molar temporary crown?

1 year. Temporaries are made for short-term wear, so they don’t get the 3 years we give final crowns. Lab-side problems like open margins, open contacts, a high bite, a crown that won’t seat or the wrong shade get remade free. Changing the shade or material later isn’t free, and neither is a remake after you asked us to go ahead on an unclear impression.

Yes. We make temporaries in composite resin or PMMA, and we can 3D print them too. Tell us how long they’ll be worn, and we won’t swap a material without your OK.

Yes. Scan it in the mouth and send that with the prep scan. We can copy its shape and its bite.

Yes. We can also supply temporary cylinders, screws and tools, at extra cost.

Please don’t. Wax softens and distorts in transit. Use a VPS bite registration, and VPS is our first choice for the impression too.

Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t promise that.

Quotes are itemized to your Rx, not one bundled price. Ask us for the price list.