Patient Situation
The patient is in their 50s and clenches during the day. There are flat wear facets on the molars on both sides, but no grinding diagnosis and no night guard .
Here’s what the dentist’s notes and the scans showed :
The plan was to crown both. But #14 came first: if its symptoms settled in a temporary, it would go to a final crown. If they didn’t, the plan would change, and that’s a clinical call. Either way, the dentist needed 8–10 weeks of watching .
Why These Molar Temporary Crowns Came to a Lab
The dentist made bis-acryl temporaries at the chair on prep day . That was fine for a couple of weeks. For 8–10 weeks on a clencher, the dentist wanted milled PMMA.
There’s some data behind that. A within-patient study of 22 people needing provisionals on premolars and molars with root canals measured the best fracture resistance and margins on milled PMMA, against self-cure PMMA and printed resin. It was short term, and those teeth had root canals, unlike #14. Still, it’s the closest match we’ve got for a molar temporary crown that has to last.
The other reason was the finals. The dentist wanted whatever the molar temporary crowns proved to go straight into the zirconia crowns. A milled design is a file, so we could copy it.
What the Dentist Asked For
The Rx, condensed :
Item 4 made sense. #15 and #18 are both last teeth in their arches, and a 9-week gap is long. But it’s also where the trouble started.
What We Found When We Lined Up the Scans
We loaded the prep, pre-op, opposing and bite scans together, then ran the left and right lateral bites through the virtual articulator. Four things came up.
The thinnest spot sat under the heaviest load
With the pre-op shape copied at full contact, we measured PMMA thickness across both crowns :
| Spot | Thickness at full contact |
|---|---|
| #14 mesiopalatal cusp | 1.1 mm |
| #14 distopalatal cusp | 1.2 mm |
| #15 mesiopalatal cusp | 1.0 mm |
| #15 distopalatal cusp | 0.6 mm |
| Central fossae, both teeth | 1.4–1.8 mm |
For posterior work, we generally design in a 0.8–2.0 mm range, depending on material. On this case we set 1.0 mm as the minimum , since the crowns had 9 weeks of clenching ahead. #15’s distopalatal cusp didn’t make it.
The pre-op shape had a side-swing contact
In a right lateral move, the patient’s left side is the non-working side. The pre-op scans showed #15’s distopalatal cusp touching #18 during that move . That’s the same 0.6 mm spot. Copy the old shape, and you put a side load on the thinnest bit of PMMA in either crown.
The biggest contact on #14 was on the cracked cusp
The pre-op bite showed the largest contact on the whole quadrant on #14’s mesiopalatal cusp . That’s the cusp with the crack. “Copy the pre-op shape” plus “full contact” meant putting that load right back where the tooth hurt.
Nothing sits behind #15
With no #16, #15 has no tooth behind it, and the same goes for #18 below. If either molar temporary crown came out of contact, nothing else would hold those two teeth.
Two Questions for the Dentist
We posted the thickness and contact maps in the case’s WhatsApp group with two separate questions .
Question 1: the 0.6 mm cusp on #15
We can’t make that spot thicker without raising the cusp, and raising it would open the bite. So we asked whether the dentist could take about 0.4 mm more off #15’s distopalatal cusp and rescan #15. #15 wasn’t the tooth being watched, and it was only one cusp.
The dentist said yes. The patient came back 2 working days later, and the new #15 scan came in that day . Our lead time counts from complete records, so the clock started on that scan.
Question 2: how much bite each molar temporary crown should carry
This one had no easy answer. Here’s what we sent :
| Option | What it means | The trade-off |
|---|---|---|
| A. As written | Full contact on both, pre-op side-swing contacts kept | Holds everything, but the heaviest contact goes back on #14’s cracked cusp |
| B. Stops on both, lighter on #14, no side-swing contacts | Each tooth keeps contacts that hold it in place. #14’s are set a touch light | Less load on #14, but the patient will feel #14 as “low” at first. Needs a check at seating |
| C. #14 out of contact, #15 normal | All bite load comes off #14 | Nothing holds #14 or #19 up and down for 9 weeks, and the patient chews on #15 alone on that side |
| D. Both out of contact | The least load on either temporary | Nothing holds #15 or #18, and the final records may not match the bite from prep day |
We told the dentist we’d lean toward B. The evidence doesn’t settle it, though, and we said so.
A randomized study of 50 prepared teeth found that placing a temporary cut tooth movement between visits in upper molars (p = 0.002). That’s an argument for having a temporary at all. It tested overlay preps, published no movement values, and didn’t compare contact schemes.
On the other side, a study of unreplaced back teeth followed for a median of 6.9 years found most patients lost 1 mm of space or less, and the opposing tooth came down 1 mm or less in 99% of cases. Movement happens, but over years. Neither paper picks A, B, C or D for you.
The dentist chose B . Which tooth carries how much bite is a clinical call, and so was the choice.
How We Built Each Molar Temporary Crown
Design
We started from the pre-op scan and only changed what the dentist’s choice required :
| Feature | What we did |
|---|---|
| Outer shape, cusp heights, cheek-side profile | Copied from the pre-op scan |
| Centric stops on #15 | Normal contact on the marginal ridges, the central fossa and the palatal cusp tips |
| Centric stops on #14 | The same contact areas, set 0.05 mm short of full contact |
| #14 mesiopalatal cusp (the cracked one) | Kept its shape, with the lightest contact of any spot on #14 |
| Side-swing contacts | None on either crown. #15’s distopalatal inner slope came down 0.2 mm to clear #18 in a right lateral move |
| Left lateral move | The natural canine, #11, does the guiding. #14 and #15 clear by 1 mm of movement |
| Contacts | Normal with #13 and between the two crowns. Nothing behind #15 |
| Minimum PMMA | 1.0 mm everywhere after #15’s new prep, including the trimmed slope |
That last row needed a check. #15’s distopalatal cusp came to 1.0 mm at the tip after the new prep, and 1.2 mm on the inner slope . Taking 0.2 mm off that slope left it at 1.0 mm, right on the minimum.
The dentist got the thickness map and the contact map in the preview, and approved them the same day .
Milling and finishing
We milled both molar temporary crowns from a PMMA disc in A3 . We stock PMMA from Ivoclar and Aidite. The technician polished the occlusal and side walls to a high shine.
That polish isn’t just for looks. A split-mouth study of 20 adults who needed molar crowns counted fewer S. mutans on milled PMMA temporaries than on conventional PMMA at one and three weeks. It measured bacteria counts, not gum disease, but 9 weeks is a long time to wear a rough surface.
Checks before shipping
QC checked both crowns against the Rx and the approved design: margins, the inside surface, the seat, contacts, the bite in centric, protrusion and side moves, shape, polish, and no cracks or voids. They shipped on working day 5 in a foam-filled box, with the tracking number sent that day .
Wearing the Temporary Crowns for Molars: 9 Weeks
The weeks below count from the day the lab temporaries went in, about 2 weeks after prep . Before that, the patient wore the chairside ones.
That adds up to about 11 weeks in temporaries. The dentist planned it that way, and it’s worth planning. A retrospective study of 15,879 restorations linked a longer time in an interim restoration with a higher risk of the tooth losing vitality (p < 0.001). That’s a link, not proof of cause, but it’s why a long wait should have a reason and an end date.
What the dentist reported :
Did the Bite Hold? Checking at Week 9
This is where option B either held up or didn’t. Before taking the temporaries off, the dentist scanned the bite with them still in place . We laid that scan over the bite scan from prep day, lined up on the upper teeth from #13 forward.
At the cusp tips of #18 and #19, we couldn’t see a change bigger than 0.1 mm . The left lateral move was still on the canine.
That’s one patient over 9 weeks. We can’t say option B is why nothing moved, and with drift that slow, it might not have moved under C or D either. What we can say is the final crowns went onto the same bite the case started with.
The Finished Temporary Crowns for Molars: Targets and Results
From the Temporaries to the Final Zirconia Crowns
With #14’s watch over, the dentist took the temporaries off and scanned the preps . We built the finals in monolithic zirconia, on the same prep as the temporaries.
| Temporaries | Final crowns | |
|---|---|---|
| Material | Milled PMMA | Monolithic zirconia |
| Outer shape and cheek-side profile | From the pre-op scan | Copied from the temporaries’ design |
| Stops on #15 | Normal contact | Same layout, normal contact |
| Stops on #14 | 0.05 mm light | Same layout, back to full contact at the dentist’s request |
| Side-swing contacts | None | None, copied from the temporaries |
| #15 distopalatal slope | Trimmed 0.2 mm | Same trimmed slope |
Both finals shipped on working day 6 . The dentist touched up one contact on #14 at seating and nothing else . Nobody had to guess where the stops should go, because the patient had already chewed on the molar temporary crowns for 9 weeks.
Sending Temporary Crowns for Molars Like These
Got temporary crowns for molars that have to last more than a couple of weeks? Here’s how it works with us:
Every step happens in our own labs, with no outsourcing: four of them in Shenzhen and Huizhou, China, running since 2012, with about 460 people, including 100 in design, 70 in milling and 25 in QC. Our full crown and bridge work runs through the same lines. You can book a factory visit or a video visit with sales.
Istar is an FDA-registered establishment, Registration Number 3039441248, which you can check in FDA’s establishment database. The lab runs under ISO 13485, and everything is made to the dentist’s Rx. For EU clients, custom-made devices follow the MDR custom-made device procedure.
Got a molar temporary crown that has to hold for weeks? Send us the scans and the Rx as a trial case, and you can see the design before anything gets milled. Single trial cases are welcome. Send your first case or talk to us.
FAQ
What's the warranty on a molar temporary crown?
1 year. Temporaries are made for short-term wear, so they don’t get the 3 years we give final crowns. Lab-side problems like open margins, open contacts, a high bite, a crown that won’t seat or the wrong shade get remade free. Changing the shade or material later isn’t free, and neither is a remake after you asked us to go ahead on an unclear impression.
Can you 3D print molar temporary crowns instead of milling them?
Yes. We make temporaries in composite resin or PMMA, and we can 3D print them too. Tell us how long they’ll be worn, and we won’t swap a material without your OK.
Can you copy a temporary I made at the chair?
Yes. Scan it in the mouth and send that with the prep scan. We can copy its shape and its bite.
Do you make molar temporary crowns on implants?
Yes. We can also supply temporary cylinders, screws and tools, at extra cost.
Can I use a wax bite with physical impressions?
Please don’t. Wax softens and distorts in transit. Use a VPS bite registration, and VPS is our first choice for the impression too.
Do you take rush cases?
Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t promise that.
How do you price temporary crowns for molars?
Quotes are itemized to your Rx, not one bundled price. Ask us for the price list.