FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Veneers
E.max

Upper and Lower Veneers Case: 16 e.max Units, One Bite Plan

This upper and lower veneers case is 16 pressed e.max veneers, ten upper and six lower, on an adult with worn edges in both arches . The Rx asked for more length on top and on the bottom, with no change to the vertical. Both of those can’t fully happen at once, because every 0.1 mm added to either edge also adds 0.1 mm of overlap between them.

So we planned these upper and lower veneers as one bite, and we showed the dentist the problem before anyone prepped a tooth.

Final design · 16 veneers, both arches
#4–#13
10 upper veneers
#22–#27
6 lower veneers
+1.2 mm on #8 and #9, +1.0 mm on #24 and #25
Target shade A1 on both arches

Upper and Lower Veneers Case at a Glance

Restoration
16 pressed e.max veneers
Upper
#4–#13
Lower
#22–#27
Length
+1.2 mm on #8 and #9, +1.0 mm on #24 and #25
Bite
Not opened; no new interferences
Shade
A1 on both arches

Patient Situation

The patient is an adult in their 40s who ground their teeth for years and has worn a night guard for a long time now . They came in about short, flat edges on both arches and a shade they didn’t like, so upper and lower veneers were on the table from the first visit. They reported no jaw pain or clicking .

Upper edges: #8 and #9 worn down to 9.6 mm, with chips along the edge and a flat incisal line .
Lower edges: #24 and #25 worn down to 7.0 mm, with dentin showing along the edges .
Bite at the centrals: 1.5 mm overjet and only 1.0 mm overbite . Molars and premolars met solidly on both sides, so the back of the mouth wasn't the problem .
Room for the lower edges: at closed bite, #24 and #25 sat about 0.4 mm from the palatal surfaces of #8 and #9 .
Color: whitened before records. Stumps were ND2 on top and ND3 on the bottom, with ND5 patches where lower dentin showed .

The dentist raised the grinding history first, since the ADA says veneers may not be a good choice for people who clench or grind. They talked through a more conservative route with the patient. The patient chose ceramic and agreed to keep wearing a guard .

What the Dentist Asked For

From the Rx for these upper and lower veneers, and from our WhatsApp thread :

Veneers on #4–#13 and #22–#27 in pressed e.max. The smile video shows the upper teeth back to the first premolars, and the lower canine-to-canine group shows in speech. The lower premolars barely show, so leave them alone.
Add 1.2 mm to #8 and #9, and 1.0 mm to #24 and #25, tapering off toward the canines.
Don't open the bite.
No new interference in protrusive or lateral moves.
Target shade A1 on both arches, with the lower teeth reading the same as the upper.
Keep the premolars' chewing surfaces out of it. The veneers stop on the buccal.
Show me a wax-up before I prep, and send the final design for approval.

The Technical Problem With Upper and Lower Veneers Here

On top and bottom veneers, length on an upper edge and length on a lower edge don’t work separately. With the vertical held, they stack. On the centrals, the Rx took the overlap from 1.0 mm to 3.2 mm (1.0 + 1.2 + 1.0) .

Our first wax-up showed what that does. With 1.0 mm added and only 0.4 mm of room, the lower edges ran about 0.6 mm into the palatal surfaces of #8 and #9 at closed bite, right where the molars still needed to meet . The protrusive path started with a step too. Our design preview flags dynamic interference like this, so we marked it up and sent it over.

This isn’t just a lab quirk. A clinical report on lower veneers warns that lengthening lower incisors can create protrusive interference with restored upper teeth, and it says to plan guidance from the start.

Three Ways Out, and the Dentist's Call

Option#8, #9 added#24, #25 addedOverlap at centralsWhat it costs
1. Keep the Rx+1.2 mm+1.0 mm3.2 mmPalatal enamel on #8 and #9 has to come off to make room
2. Hold the lower edges back+1.2 mm+0.4 mm2.6 mmLower edges end up 0.6 mm shorter than asked
3. Open the bite+1.2 mm+1.0 mmDepends on the openingBack teeth need restoring too, which the Rx ruled out

All values .

Option 3 was out early, because the dentist didn’t want posterior work and the back teeth were stable. A review of occlusal vertical dimension notes that ways of measuring vertical loss lack consistency, so worn edges alone didn’t make the case for opening up.

We didn’t push option 1 or 2. That decision belongs to the dentist. They picked option 2 and confirmed it in writing, because they’d rather give up some lower length than cut sound palatal enamel .

How the Mock-Up Changed the Upper and Lower Veneers Plan

The dentist made a mock-up chairside from a silicone matrix off our printed wax-up model, and the patient wore it for five days (a clear silicone matrix the lab made on the printed wax-up model). A three-year study of 79 upper and lower e.max Press veneers on worn teeth used the same order: wax-up, then mock-up, then prep. That study left out patients with parafunction, so its 98.7% survival doesn’t speak for a patient with this history.

The lower edges felt fine. The upper edges didn’t. On F and V sounds, #8 and #9 pressed too hard into the lower lip, so the dentist trimmed about 0.2 mm off the upper edges of the mock-up, rechecked speech and sent us a new scan . The whole upper set moved with them, which brought the overlap down to 2.4 mm .

Here’s the plan that went to production:

TeethPre-op length (mm)Rx askedFinal addedFinal length (mm)
#8, #99.6+1.2+1.010.6
#7, #108.0+1.0+0.88.8
#6, #119.6+0.6+0.410.0
#4, #5, #12, #13–NoneNoneUnchanged
#24, #257.0+1.0+0.47.4
#23, #267.4+0.8+0.47.8
#22, #279.0+0.6+0.39.3

How We Met Each Requirement on These Top and Bottom Veneers

No opening of the bite

The premolar veneers stay on the buccal, so their chewing surfaces and the molars kept holding the vertical. We asked for the scans in order: pre-op and mock-up scans of both arches, then upper prep, then lower prep, with a bite scan after each . There was always something unprepared to line the arches up against. A VPS bite registration backed that up. Skip wax on a case like this, since it can soften and distort in transit.

We copied the approved edges from the mock-up scan instead of redesigning them, so function carried over along with the look.

A smooth path in protrusive

In the design, we marked every lower contact on the palatal surfaces of #6–#11 and sent that map to the dentist before the prep . They kept the upper palatal finish lines about 1 mm clear of those marks, so the lower edges don’t cross a join between ceramic and tooth .

The lower edges then got a clean, rounded profile and a polished surface, since they run against natural palatal enamel . We checked centric, protrusive and lateral moves on printed models before the veneers left the lab.

Enough ceramic on small lower teeth

A lower incisor doesn’t give you much to work with on a set of upper and lower dental veneers. That clinical report aims for about 0.4–0.6 mm of reduction on these teeth and uses a pronounced incisal chamfer to avoid thin edges, which can crack during bonding.

The dentist took about 0.4 mm facially on the lower teeth and 0.5 mm on the upper teeth, and wrapped the edges on #6–#11 and #22–#27 . Wrapping fits the data too: a systematic review of 25 studies and 6,500 veneers found fewer failures with incisal coverage than without it. Fracture was the most common complication, followed by debonding, and both showed up more in the early years.

Dentin on the lower edges

Wear had already exposed dentin on #24 and #25, so the dentist marked it on a photo, about a quarter of the bonding area on each . That’s worth knowing up front. A review of bonding substrates reports better results on enamel than on dentin or old composite, though it only covers six studies. A 36-month study of 130 pressed veneers found similar results in both jaws, but more interventions when over half the preparation was exposed dentin.

So the dentist used the mock-up to guide the reduction and kept the rest of the prep in enamel .

One shade across two arches

Same target, different starting point, and that’s the catch with upper and lower dental veneers. The lower veneers are thinner and sit on darker stumps, so the same ingot would’ve read darker than the upper set. We planned color in a set order: stump shade, then target, then layers. That gave us a slightly less translucent ingot on the lower set than on the upper set, both aiming at A1 (IPS e.max Press LT A1 on the upper set, MT A1 on the lower set).

We cut back only the incisal third, with less edge translucency on the short lower teeth so they wouldn’t go gray (about 0.3–0.5 mm, layered with IPS e.max Ceram incisal porcelain). Both arches were pressed and finished together by the same technician (one ingot batch, the same firing cycles), and each layer, stain and batch went into the case record.

Why pressed e.max for this set

The dentist specified it for these top and bottom veneers, and all our e.max veneers are pressed. A 2025 review of ceramic veneers found no survival difference between feldspathic, leucite-reinforced and lithium disilicate at 10.4 years. Lithium disilicate had the lowest complication rates, with 6.1% technical. Those are pooled numbers, though, not a forecast for one patient.

Making the Upper and Lower Veneers, Step by Step

Planning round . We checked the pre-op scans and smile video within one working day and sent the first wax-up on working day 3. When the trimmed mock-up scan came back, we updated the upper edges to match.
Records check, day 1 . We checked both prep scans, the bite scans, the VPS bite and the shade photos. A blurry margin or a bad bite would've meant a rescan.
Design, days 2–3 . The preview went out on day 2 with lengths, overlap and contact marks, and written approval came on day 3. Those contours went on file, so every later step worked from one record.
Pressing and hand work . We pressed all 16 upper and lower veneers, then a technician with 10+ years on front-tooth cases did the incisal layering and surface finish, working from the stump and shade photos.
Final inspection. Our QC team checked margins, inner surfaces, seating, contacts, bite, form and polish, under standard light, and looked for cracks, pores and chips. Contacts, bite and margins get a second look after glazing, and the finished set gets compared against the approved design file.
Packing . A foam-filled box, with each veneer labeled by tooth number and the upper and lower sets kept apart.

Dentist and Patient Feedback on the Upper and Lower Veneers

The dentist tried in the upper and lower veneers with paste, then sent us photos and notes on WhatsApp . In short:

Dentist

the edges matched the mock-up, and the arches lined up with the planned contacts. One contact on #25 ran a little heavy, so they eased it chairside, polished it and bonded the set with resin cement at the same visit .

Patient

happy with the upper edges and the color. They noticed the lower teeth are a bit shorter than the first picture they’d seen, but they said speech felt normal and they didn’t want anything changed .

Finished Upper and Lower Veneers: Design Goals and Results

Design goalHow it was checkedResult
Vertical unchangedMolar contacts on the printed models, then at bondingSame contacts as pre-op
Overlap at the centrals: 2.4 mmFinished veneers against the design file2.5 mm
Lengths as approvedFinished veneers against the design file, measured on the modelWithin 0.1 mm
No new interference in protrusive or lateral movesPrinted models, then the dentist’s check at bondingOne heavy contact on #25, adjusted chairside
Lower arch reads the same as the upperStandard light at the lab, try-in photosNo visible step between arches
Lip clear on F and V soundsDentist’s speech check at try-inPassed

It wasn’t all a win. The lower edges finished 0.6 mm short of the original ask on the centrals, and the upper centrals finished 0.2 mm short . That was the price of keeping the vertical and the palatal enamel, and the dentist chose it knowing that.

The dentist also ordered a new night guard from a post-bonding scan, so the patient goes home with protection that fits the new edges .

What to Send Us for Upper and Lower Dental Veneers

Before the prep: pre-op scans of both arches in PLY, a closed-bite scan, a full-face smile photo, a resting-lip photo, and a short video of speech and smiling. Tell us how much length you're hoping for on each arch.
After the prep: prep scans of both arches, one arch at a time, with bite scans and margins marked by hand. Add a mock-up scan if the patient tried one, and a VPS bite. We work with 3Shape TRIOS, Medit, iTero, CEREC, Shining3D Aoralscan and Planmeca, plus any scanner that exports open files. Upload through our digital case submission.
Photos: retracted shots with the target tooth, its neighbor and a shade tab in one frame, plus stump shade photos for each arch. Mark any exposed dentin.
On the Rx form: tooth numbers, target shade, translucency, surface texture, proportions, midline, smile line, overjet and overbite, any limit on the vertical, and what you want the guidance to do.

Upper and lower veneers generally take 5–7 working days in our lab. A diagnostic wax-up stage runs 2–3 working days, and design approval adds 1–2 days.

Who Made It

These upper and lower veneers went through our CAD design team (about 100 people), our ceramic and metal department (about 70) and a separate QC team of about 25. They work inside Istar Dental Lab’s four labs in Shenzhen and Huizhou, China. We’ve been running since 2012, with about 460 staff and no outsourcing.

Istar Dental Lab is an FDA-registered establishment (Registration Number 3039441248), which you can look up in the FDA establishment registration database. Our labs run an ISO 13485 quality management system.

Upper and Lower Veneers FAQ

Do I have to send upper and lower veneers at once?

No. You can send the upper arch now and the lower arch later. We keep approved contours on file, so the second arch can start from them. Send new shade photos with it, since we’ll be matching ceramic that’s already in the mouth.

Sure. How many teeth to restore is your call, and we’ll make what’s on the Rx. Send a smile photo that shows the lower teeth, so we can see what the upper set will sit next to.

Send a facebow record and tell us the planned bite. We’ll copy that record into a try-in for you to check before anything final gets made.

Yes. Send VPS impressions of the prep and opposing arches.

Yes. Old restoration photos work too, and so do sketches.

Zirconia, which is stronger and more wear-resistant, and lab-made composite. Compare them with pressed e.max veneers, or see what else our e.max lab makes. We won’t swap a material without your OK.

Yes. Tell us early, and it won’t affect the lead time or the fee.

We’ll make it to the Rx with no sign-off form, but a remake caused by that design isn’t on us.

Open margins, open contacts, high bite, a veneer that won’t seat, inaccurate color, visible flaws and poor shape are ours to fix for free. Changing the shade or material afterward isn’t free, and neither is a case you asked us to try on an impression we’d already flagged as poor.

Veneers carry our 3-year warranty. You pay to send a case in, and we pay to ship finished work back, remakes included.

Rush service is free for clients who send us 10 or more cases a month. We guarantee the ship date, but not the arrival date, because customs times vary.

We don’t publish prices on the website. Ask for our price list, and we’ll quote each case item by item to your requirements. Ongoing partnerships suit clinics with a regular case flow.

Send Us Your Next Upper and Lower Veneers Case

Got a request for top and bottom veneers, with worn edges and not much room between them? Send the pre-op scans, and we’ll show you what fits before you prep. Single trial cases are welcome, and you can see the work for yourself on a factory visit or video tour.