FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Crowns & Bridges
Zirconia

20 Zirconia Crowns Case: Molars Stay, Provisionals Get Copied

These 20 zirconia crowns went on #4–#13 and #20–#29 . All eight molars stayed as they were, so the bite had no room to grow . The patient still wanted longer front teeth. That’s the whole puzzle: more tooth, same vertical.

Final design · 20 single crowns, molars natural
Upper
10 crowns
Lower
10 crowns
Molars
Natural · hold the vertical
No splinting
Canine guidance on #6, #11, #22 and #27

20-Unit Zirconia Crowns Case at a Glance

Restoration
20 separate multilayer zirconia crowns
Shade
A2 body, necks close to A3
Vertical
Kept as is; the natural molars hold it
Guidance
Canine guidance on #6, #11, #22 and #27
Provisionals
Wax-up, then PMMA; copied once approved
Habit
Grinds at night

Patient Situation

Before we planned the 20 zirconia crowns, the dentist’s notes, scans and photos showed this:

Front teeth: flat, worn edges. #8 and #9 looked short in a full smile, and the lower incisors had worn the most .
Premolars: large old composites, some with chipped edges .
Molars: all eight natural and solid, with even contact on both sides. Third molars are long gone .
Overbite: down to about 0.5 mm, because of the wear .
Stumps: all vital, no posts, similar color. Masking wasn't the fight on this one .
Habits: grinds at night, with no guard before this .
Patient's ask: longer front teeth, and no more patching fillings .

Why This 20 Unit Zirconia Case Stopped at the Premolars

Saying 20 zirconia crowns only gives you a count. It doesn’t tell you the diagnosis, and it doesn’t mean every tooth gets a crown. Here the count came from one finding: the dentist saw no reason to touch sound molars .

That choice sets the limit. If the molars keep touching where they touch now, the vertical stays where it is. Raising it would have meant restoring all eight molars too, so 28 units, not 20 .

Why These Aren't Full Mouth Zirconia Crowns

They can look like full mouth zirconia crowns in a photo, but the back of the mouth wasn’t part of this. The dentist also didn’t chase a set number for the bite. A consensus statement on occlusal vertical dimension reports a mean interocclusal distance of 3.0 mm, but values run from 1 to 9 mm. Any decision on vertical stays chairside.

What the Dentist Asked For

The Rx, condensed :

20 zirconia crowns, all separate. No splinting.
Keep the current vertical. The molars hold it.
Wax-up first, then PMMA provisionals. Copy the provisionals once they're approved.
Multilayer zirconia, no porcelain on top.
A2 body on all 20. Warm necks, close to A3, so the premolars don't jump away from the natural molars.
Canine guidance on #6, #11, #22 and #27. Keep the premolars out of excursions.
Show the design before milling.
Ship all 20 together.

That last line matters earlier than you’d think. Splitting an order can be done at the design stage or before milling starts. Once the crowns are on the machine or in the furnace, usually it can’t. So we settled it before any milling.

How the Wax-Up and Provisionals Set the Plan

First records

The dentist sent STL and PLY scans of both arches, a bite scan, a VPS bite record, photos and shade tabs . Scans go through our digital workflow, and VPS is what we want for a bite on a case this size. Wax can soften and deform in transit, and a bite that drifts on the way here throws off everything after it.

Using those records, we built a digital wax-up for the 20 zirconia crowns, inside the existing vertical :

#8 and #9: edges 1.5 mm longer .
#24 and #25: edges 0.5 mm longer .
Overbite: back up from about 0.5 mm to 2.5 mm, since the added length has to overlap somewhere .

Six weeks in PMMA

Once the wax-up was approved, we made the provisionals from it in PMMA, and the dentist placed them on the prepared teeth . The patient wore them for six weeks . Two things came up :

What showed upWhat the dentist changed chairside
“S” sounds felt off, and the edges of #8 and #9 looked a touch longTook 0.5 mm off both edges, so the net gain is 1.0 mm and the overbite is 2 mm
#24 chipped once, at nightFlattened the guiding slope on the palatal of #8 and #9

Those adjusted provisionals became the blueprint for the 20 zirconia crowns, not the first wax-up. That’s the point of this stage. There’s published support for working this way. Each of these reports covers one patient whose vertical was raised, so they back the method and not this exact bite:

One full-mouth case report built its zirconia crowns from 3D scans of the provisional crowns.
Another full-mouth report watched the provisionals for three months, then moved the guidance over with a custom guide table. Lingual adjustment on the upper front teeth ended up minimal, on metal-ceramic crowns.

How We Moved the Bite and Shape Into 20 Zirconia Crowns

What came in for the final design

Before the final prep scan, the dentist scanned the adjusted provisionals in the mouth, both arches and the bite . Then the provisionals came off, the prep margins got cleaned up, and the dentist scanned the prepared arches .

Here’s where the untouched molars paid off. With 20 prepared teeth out of contact, the molars were the only teeth touching. That gave us a stable stop on both sides . We also got a fresh VPS bite as a cross-check .

RecordWhat it controlled
Adjusted provisional scanTooth length, edge position, outer shape
Palatal surfaces of the provisionalsGuidance on the front teeth and canines
Prep scansMargins and inner surfaces
Molar contact in the bite scanVertical and arch relationship
VPS bite recordCross-check on the bite scan
PLY scans, photos and tabsGum levels, shade map, surface detail

We lined up the provisional scan and the prep scan using the molars and palate as shared references, then copied the outer shape onto each crown . Our senior designer checked the bite and shape before the design went further, and a technical supervisor gave it a second review because of the case’s complexity .

The Technical Problem in This 20 Unit Zirconia Case

Copying the shape onto 20 zirconia crowns was the easy part. The thickness check was where it got tight :

TeethThinnest wall after copyingDisc minimum for this case
#24, #250.6 mm, incisal lingual0.8 mm
#23, #260.8 mm0.8 mm
Everything else0.9 mm or more0.8 mm

The lower centrals were the worn teeth, and they had the least room. You can’t just thicken them either. Thicker lingual means new contact with the upper palatals, and those were approved already.

Minimum thickness isn’t one number across zirconia, either. In one lab study on premolar crowns, manufacturer minimums were 0.5 mm for 3Y and 1.0 mm for 5Y. Going by that study, 1.2 mm of resin-bonded 5Y matched 1.0 mm of 3Y with RMGI for fracture resistance. That was on printed dies, and its authors still say to follow the maker’s minimum. So we go by the disc that’s actually in the case.

We paused the case and sent the dentist the thickness map with four ways out :

OptionWhat it doesThe catchDentist’s call
1. Mill as copiedKeeps every approved shape, no new prep0.6 mm on #24 and #25, under the disc minimumNo
2. Raise the verticalAdds room everywhereAll eight molars would need work, and the plan changesNo
3. Shorten #24 and #25, or reshape the palatals of #8 and #9No new prepChanges the look or the guidance the patient already testedNo
4. Take 0.3 mm more off #24 and #25 with a guideKeeps the shape and bite, gets the wall to 0.9 mmOne short extra visit, and a rescanYes

We printed a small reduction guide from the design, and the dentist used it on those two stumps, then rescanned them . Only those two teeth changed .

Design approval

The preview for this 20 unit zirconia case went to the work group with occlusal, facial and lingual views, plus contact points . The dentist asked for softer distal corners on #7 and #10, 0.2 mm each, then approved it in writing . Front esthetic and bite-change work always gets approved before production here.

Disc, sintering and color

The 20 zirconia crowns went into two discs from one material lot, upper in one, lower in the other . We set the front teeth so the more translucent zone sat at the incisal third. The premolars went lower in the gradient, because they carry more bite and don’t need the same see-through edge .

Color across 20 zirconia crowns needs more control than color across two:

Sintering: a locked program, with temperature, ramp rate and hold time fixed. We log each furnace curve.
Shrinkage: set from the zirconia maker's numbers and checked with test pieces on each batch.
Same references: same material batch, same approved shade reference and photos, for every crown in the case.
Reference piece: a control sample in each batch, so QC can compare color, translucency and form across batches.

Stain and finish

Front esthetic work usually goes to technicians with 10 or more years at the bench. Stain followed the Rx: warm necks, a light gray-blue band below the incisal edges on #6–#11 and #22–#27, and less effect on the premolars . Every stain, dilution and firing went on the case file .

Finish on the 20 zirconia crowns was split by zone :

Facial: thin glaze, hand-polished back to a natural shine.
Palatal guidance and all occlusal contacts: polished, no glaze.

The polish had a specific job here. #4 and #13 land partly on the natural lower first molars, #30 and #19 . An umbrella review on opposing enamel wear found polishing wears enamel less than glazing does. With a night grinder and two natural molars in the path, we weren’t going to leave glaze on those contacts.

Final checks

A QC technician who didn’t make the 20 zirconia crowns ran final inspection, using a checklist longer than usual because of the case’s size :

Identity: all 20 crowns against the tooth chart .
Fit: margins, inner surfaces and seating on printed models.
Contacts: tightness, crown by crown. A National Dental PBRN study of 3,750 single-unit crowns named proximal misfit, marginal errors and esthetic failures as the top reasons for rejection. So that's where we look hardest. On this case, that's 18 contacts between crowns, plus the four against the natural molars .
Bite: centric, protrusive and lateral.
Against the approval: scanned finished crowns laid over the approved design . Then color, translucency, texture and symmetry, under a standard light.

Photos of the QC went to the dentist before shipping .

The Finished 20 Zirconia Crowns

The dentist seated the 20 zirconia crowns one half-arch at a time, cementing in small groups and checking the next crown after each group . Cement choice and seating order were theirs.

Design target
What happened at seating
Molars still hold the vertical
Same molar contact as before prep, per the dentist's shim stock check
Edge position from the provisionals
#8 and #9 matched the provisionals, no length changes
Canine guidance, premolars out of excursions
One light touch on #13 in right lateral, adjusted and re-polished chairside
#24 and #25 hold their wall
Delivered at 0.9 mm or more
No step from premolar to molar
Warm necks read close to the molars in smile photos
All 20 fit on first delivery
No remakes

What the dentist told us

The dentist said the seating took less chair time than they’d planned, since the bite had already been worked out in the provisionals . Then they sent a new scan and ordered a night guard to go over the new crowns .

What the patient told us

Through the dentist, the patient said the new teeth felt familiar, because they’d already spent six weeks with that shape .

What We Gave Up

Length: #8 and #9 gained 1.0 mm instead of the first plan's 1.5 mm .
Tooth structure: #24 and #25 lost another 0.3 mm to keep the shape .
Time: a six-week provisional stage, plus one extra visit and rescan .

What These Crowns Can't Promise

We have no long-term follow-up on these 20 zirconia crowns yet . Published data won’t fill that gap either. In a systematic review of tooth-supported zirconia, 94.4% of the monolithic units were single crowns. So those numbers don’t tell you how full mouth zirconia crowns, or any 20-crown set, will hold up. Upkeep still matters too, and the night guard is part of that.

Send Us Your Own 20 Unit Zirconia Case

Planning your own set of 20 zirconia crowns? Here’s what helps us most:

  • Tell us the plan: tooth chart with exact numbers, and which teeth hold the vertical.
  • Scans: both arches plus bite, or send impressions and models. Add PLY for front teeth.
  • Provisionals: a scan of the approved ones in the mouth, with any chairside changes already made.
  • Photos: full smile, rest and shade tabs in frame.
  • Rx: use our Rx form. Write the guidance you want, plus “copy provisionals.” Here’s how to send a case.
  • Lead time: generally 5–7 working days at the lab for final crowns. Design approval can add 1–2 days, and time spent waiting on replies or missing files isn’t counted.
  • Shipping: you pay to send work to us, and we pay to ship finished work back, remakes included.
  • Warranty: 3 years on crowns. Open margins or contacts, a high bite, a crown that won’t seat, a wrong shade or poor shape all get remade free.
  • Quotes: itemized to your Rx, not one bundled price. Ask for the price list.

The same steps apply if your plan grows into full mouth zirconia crowns with the molars included.

All of it gets made in our own four labs in Shenzhen and Huizhou, China. We’ve been at it since 2012, with about 460 people, including about 100 in CAD design. At peak, we make about 15,000 zirconia single crowns a month, and nothing gets outsourced. Factory-wide, 95% of cases pass final inspection the first time, and clients send back 2–3%. Those are two separate numbers, and neither is specific to this kind of case.

Istar is an FDA-registered establishment, Registration Number 3039441248, which you can look up in FDA’s establishment database. The lab runs under ISO 13485. You can also book a factory or video visit.

Got a 20 unit zirconia case where the bite can’t move? Send one as a test case, and we’ll show you the design before we mill anything. Send your first case or talk to us.

FAQ

What if I want a thin area left as is?

Your call, and you don’t need to sign anything. We flag it and ask once. If you still want it, we make it to the Rx. Problems from that choice, remakes included, aren’t ours to cover.

If it fit but cracked, we can usually remake it from the old data. If it’s a seating, margin or bite problem, send a new scan or impression. Each case has its own number tied to the technician, material batch and stain record, so we can work back to how that crown got its color.

A change of shade or material from your side isn’t covered as a free remake. Same goes for a bad impression you asked us to try anyway. Before milling is a better time to change things: a design change made soon after approval usually won’t affect price or lead time.

Yes. Ask, and we’ll give you brand, origin, batch number and certificates for that case. If you want a certain brand, tell us on the Rx. We won’t swap a material without your OK.

Rush is free for clients sending 10 or more cases a month. We guarantee the ship date. Arrival depends on customs, so we can’t guarantee that part.