FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Case study
Orthodontics
Retainers

Essix Retainer Temporary Tooth Case: A #9 Pontic That Stays Off the Graft

This essix retainer temporary tooth case is one upper appliance for #9 (FDI 21), ordered while the tooth was still in the mouth. The dentist needed a front tooth that looks right and a surgical site left alone, and those two goals pull against each other.

This essix retainer temporary tooth was built for a gum line that didn’t exist yet. Nobody could try it in until the day it had to work.

Final design · Essix retainer with #9 pontic
#8
Sheet
#9
Pontic · off the graft
#10
Sheet
No contact with the socket or graft
Posterior occlusal surfaces open

Essix Retainer Temporary Tooth Case at a Glance

Appliance
Essix retainer with a #9 pontic
Shade
A2, matched to #8
Pontic
No contact with socket or graft; out of the bite
Sheet
No edge resting on the surgical site
Delivery
In the clinic at least 5 working days before surgery
Approval
Design preview before forming

Patient Situation

The patient, in their 40s, works face to face with clients all day, so a gap for months wasn’t an option . #9 had an old PFM crown and a vertical root fracture, and the dentist judged it non-restorable . The plan was to extract, graft the socket, then place an implant about 4 months later .

The details that shaped the build :

Smile line: all of #9 shows, plus about 1 mm of gum above it.
Neighbors: #8 and #10 are firm and unrestored.
Bite: about 3 mm of overlap, with #23 and #24 touching the lingual of #9.
Habits: no grinding or clenching reported.

An implant-level temporary wasn’t on the table, since the implant was coming later. A plate-based flipper would’ve sat right on the site. So the dentist picked an Essix retainer with tooth, an option described for both pre- and post-implant patients.

What the Dentist Asked For

From the Rx :

In the clinic at least 5 working days before surgery.
No contact between the pontic and the socket or graft, with room for swelling.
No sheet edge resting on the surgical site.
Pontic out of the bite in centric and protrusion.
Posterior occlusal surfaces open, so the sheet doesn't prop the bite.
Length, form and shade A2 matched to #8.
Easy to seat and remove on a swollen mouth.
Design preview before forming.

The Technical Problems in This Essix Retainer Temporary Tooth

The tissue was still a guess

We had #9 with its crown on it. We didn’t have the socket, the graft volume or the swelling, and those decide the space under the pontic.

Clearance and looks fought each other

An essix retainer with pontic keeps the load on the teeth only if the pontic stays clear of the site. But the more room you leave, the shorter the tooth reads in this smile. Rx items 2 and 6 couldn’t both be pushed all the way.

The sheet is thinnest where the pontic needs it

A lab study of thermoformed retainers found the most thinning at the mid-labial of incisors, about 68% in its 1 mm copolyester pressure-formed lower group. Those were plain retainers, so we didn’t take that as our number. It did mean the thickness on the label wouldn’t be the thickness over #9.

Retention could work against the swelling

These appliances hold on through the natural undercuts below the contact points, with no clasps. Good on a normal day. On surgery day, the two undercuts closest to the site, at #8 and #10, could make seating a fight.

Two Ways to Relieve the Essix Retainer With Pontic

The Rx said “no contact”, but not how much space. So we paused before design, asked in the case’s WhatsApp group, and laid out two options on the scan :

OptionWhat it meansThe trade-off
A. Shorten the whole pontic1.5 mm of space all aroundSimplest for the site, but #9 ends up short
B. Hollow the tissue side1.5 mm over the socket, 1.0 mm on the palatal, 0.5 mm at the facial neckKeeps the length, with the neck running closer to the gum

We recommended B. How much tissue margin is safe isn’t our decision, so the call was the dentist’s, and the dentist went with B .

How We Met the Rx: Building the Essix Retainer Temporary Tooth

Records and the virtual extraction

The dentist sent pre-op scans in PLY, which show gum color and the neck line, along with the opposing arch, a bite scan, and smile and shade photos .

Our designer removed #9 on the scan and printed the model . Virtual extraction over a printed model is a published route for this appliance. Its impression-based counterpart is taking the tooth off a stone cast.

Building the pontic

We mirrored #8 for the denture tooth setup and hollowed the tissue side to the approved map, then reduced the lingual for the lower incisors .

Where tooth meets sheet is the weak spot on any essix retainer with pontic. So we cut a small undercut groove around the lingual and neck for the sheet to lock into, and added a tiny spot of adhesive on the lingual . Retention without adhesive has been reported, but the hollowed tissue side leaves less bulk to grip here.

Blocking out and forming

The model design blocked out the undercuts at #8 and #10, which moved most of the grip out to #3–#7 and #11–#14 .

For this essix retainer with pontic, the sheet was heated evenly, formed under steady pressure, and cooled under that pressure until it set .

Trimming

Around #9: the sheet stops on the pontic, short of the gum .
Everywhere else: the edge sits at the gum line, trimmed and polished smooth .
Posterior teeth: cut open from #3 to #5 and #12 to #14 . The step has been published before.
Inside surface: barely touched. Too much polishing in there is how you lose the fit.

Bite and QC

We checked the scans and bite record against each other, then verified on an articulator. QC measured the sheet with calipers at several points, ran a finger and eye check around the whole edge for burrs, tested seating and removal on the model, and looked for cracks and bubbles. After high-pressure cleaning, the essix retainer with pontic went into its own patient-labeled bag.

Timeline

Working dayWhat happened
0Complete records received
1Files checked, no rescan needed
2Design preview approved
7Shipped, tracking number sent that day
12Arrived at the clinic
20Surgery

The Finished Essix Retainer With Tooth: Results

CheckResult
#23 and #24 against the pontic0.5 mm clear in centric and protrusion on the articulator, confirmed in the mouth
Sheet thickness, mid-labial on #90.55 mm, against our 0.5 mm minimum for this case
Pontic contact at seatingNone, after the dentist took about 0.3 mm off the palatal side, where the graft and membrane sat fuller than the scan could predict. Checked with pressure paste
Posterior biteNot propped. One contact eased on the sheet over #8, against #25
AppearanceLength and shade accepted by the dentist. A faint line shows at the neck in a full smile

After surgery (the dentist's report)

The essix retainer temporary tooth went on without force right after surgery . At the week 1 check, it popped on and off easily, and the slight lisp from the first few days had faded . By implant placement at 4 months, the pontic hadn’t moved and the sheet was scuffed but intact, so no replacement was needed .

What it can't do

An essix retainer with tooth isn’t a fixed temporary. The patient took it out to eat, as the dentist had explained before surgery , and it needs daily cleaning. It also won’t shape the tissue the way an implant-level temporary can.

Sending a Similar Essix Retainer Temporary Tooth

Planning with us works when the surgery date is set and you can scan before the extraction. For a same-day need, an in-office thermoformer gets you there faster.

Lead time: generally 5–7 working days at the lab, from complete records. Seeing the design first adds 1–2 days. Shipping from China comes on top.
Records: intraoral scans or physical impressions. Use our Rx form and see how to send a case.
Also put on the Rx: the surgery date and the planned wear time.
Shipping: you pay to send impressions or models to us, and we pay to send the finished work back.

Everything’s made in our own labs, with no outsourcing: four of them in Shenzhen and Huizhou, China, running since 2012, with about 460 people. The retainer line also makes standard Essix retainers, and our implant team can take over for the final restoration. You can book a factory visit or a video visit with sales.

Istar is an FDA-registered establishment, Registration Number 3039441248, which you can check in FDA’s establishment database. The lab runs under ISO 13485, and every appliance is made to the dentist’s Rx.

Planning an essix retainer temporary tooth ahead of a front tooth extraction? Send us the pre-op scans and the Rx as a trial case, and we’ll come back with a relief plan before anything gets formed. Single trial cases are welcome, and regular case flow is where a partnership really pays off. Send your first case or talk to us.

FAQ

What's the warranty on an essix retainer temporary tooth?

1 year. Lab-side problems like an appliance that won’t seat, lifting edges or an inaccurate bite get adjusted or remade free. Changing the material or shade later isn’t free, and neither is a remake after you asked us to go ahead on an unclear impression.

Yes. Send records of the arch as it is now, and tell us how far along the site is.

VPS, not wax. Wax softens and distorts in transit. VPS is our first choice for the impression too.

Yes, at no extra charge, for clients who send 10 or more cases a month. We guarantee the ship date. The arrival date depends on customs, so we can’t promise that.

Quotes are itemized to your Rx, not one bundled price. Ask us for the price list.

Essix is a Dentsply Sirona trademark, though the name often gets used for this type of clear thermoformed retainer. If you want a specific sheet brand, write it on the Rx. We won’t substitute a material without your OK.