FDA Reg. 3039441248 · EU MDR · UK MHRA · ISO 13485
9:30–18:00 China time (UTC+8)
Zirconia
Implants

Implant Full Zirconia Crown: Strong Where It Matters, Right at the Interface

Full zirconia is the easy part. What decides how an implant full zirconia crown performs is everything around it: the right library, a well-placed screw channel, a clean Ti-base bond and an emergence profile your patient can keep clean.

At Istar Digital Dental Lab, that’s where our implant team puts its attention. We check your implant details before design, show you the design before we mill and inspect the interface again before your crown ships. You get a crown that seats the way you planned, with fewer surprises at the chair.

Send us one case and see the difference for yourself.

01 · Why Istar

Why Dentists and Labs Send Implant Crowns to Istar Digital

An implant team of about 80 people. Implant work isn’t a side line here. It has its own department, supported by about 100 CAD designers, across four labs we own in Shenzhen and Huizhou. Founded in 2012, Istar Digital keeps every case in-house, from design to final inspection.

You see the design first. We send the design, including the emergence profile, for your approval before milling, with two free revisions. You stay in control of the clinical decisions.

Your system, your library. Most implant systems on the market are supported. If your library differs from ours, we use the one you provide.

Straight answers on cost. Quotes are itemized by unit, material, components and design complexity. You can confirm the full cost before production starts.

A 3-year warranty. Implant restorations are covered for three years, and we pay to ship finished work back to you, including remakes.

02 · Material

Why Choose a Monolithic Zirconia Implant Crown

A monolithic zirconia implant crown is milled from one piece of zirconia, with no veneering porcelain to chip. In a meta-analysis of randomized trials on posterior implant crowns, one-year chipping was 0% for monolithic zirconia and 7.61% for metal-ceramic, with no significant difference in bone loss or implant failure.

It’s the natural choice for molars and premolars, heavy occlusal loads, bruxism and limited occlusal space. For bruxers, we add occlusal thickness where space allows and keep contacts even, with no lateral load on the implant.

Choosing the Right Zirconia

Choose zirconia for the case, not for the biggest number on the label. As yttria content rises, zirconia becomes more translucent and less resistant to fatigue. One published comparison shows the trade-off:

Zirconia typeFlexural strengthFatigue strengthBest suited to
3Y-TZP778–871 MPa537–640 MPaMolars, bruxism, reduced thickness
4Y-PSZ534 MPa304 MPaA balance of strength and esthetics
5Y-PSZ470–485 MPa232–336 MPaEsthetic single units with enough thickness

These are study results, not product specifications; brand, test method and sintering all change the numbers.

In practice, we offer single-layer zirconia for posterior and bruxism cases and multilayer zirconia, with its cervical-to-incisal gradient, for anterior cases that need strength and a natural look. You can name a brand on the prescription if it’s available to us in China, and we’ll never switch material without your consent.

03 · Retention

Screw-Retained or Cement-Retained?

Where the implant position allows it, we recommend screw retention. The crown stays retrievable and there’s no cement to chase around the implant. A five-year randomized trial reported overall complications in 68.4% of cemented and 22.7% of screw-retained zirconia-based crowns. The sample was small, and another five-year trial found similar outcomes for both, so the case still decides.

Cement retention makes sense when the implant angle would put the access hole on the facial surface, or when there’s enough room and the esthetic demand is very high. It needs enough abutment height for retention, so tell us the space you have.

If the channel falls in the wrong place, there’s usually a way around it: an angled screw channel with a custom abutment, a multi-unit abutment, a reshaped crown that moves the access hole lingually, or cement retention as the last option. We can provide Ti-bases, angled screw channel solutions and multi-unit abutments.

Not sure which design fits? Send the scan and available space, and we’ll suggest the options.

04 · Fabrication

How Your Implant Crown Is Made

1. We check the implant details

A library mismatch can produce a crown that looks right on screen but has the wrong connection or rotation. So before design, we check the implant brand, platform, connection, diameter, scan body and library against your case. A photo of the packaging label is the quickest way to confirm. If something is missing or conflicts, we pause and ask rather than guess.

2. We design around the implant

We plan the screw channel along the implant’s long axis and place the opening in the occlusal fossa where possible, away from contacts. The software checks the channel path and the zirconia wall around it. The emergence profile is shaped from your healing abutment or provisional scan, with a smooth, cleansable transition rather than a bulky contour.

3. You approve the design

You receive the design as images or a 3D-printed model. Previews flag anything we’re concerned about, such as an unclear margin, occlusal interference or a profile that would be hard to clean. Your approval comes before milling, and the final design file is yours to download.

4. We mill, sinter and bond with controlled steps

Sintering programs are fixed and every furnace curve is logged. Shrinkage compensation is checked against test pieces for each material batch. For a zirconia crown on a titanium base, bonding follows a set protocol: the implant interface is protected, the bonding surface is air-abraded with 50 µm alumina and cleaned, an MDP primer goes on, and the cement gap is kept at 20–50 µm. Excess cement is removed before it can reach the interface.

That care has a clinical reason. In a four-year study of monolithic zirconia on prefabricated Ti-bases, cumulative survival was 100% for bonded crowns and 85% for mechanically retained crowns.

5. We inspect before it leaves

Final release belongs to inspectors who don’t make restorations. On every implant crown, they check that the interface sits accurately on the analog, the screw turns in smoothly through the channel, the crown seats passively without rocking and every component matches. Margin, contacts and occlusion are checked against the design you approved. Inspection photos are available on request.

Screws and small parts ship in a separate bag labeled with your case number.

05 · Components

OEM or Compatible Components: Your Choice

We recommend OEM components first for fit and long-term stability. Validated compatible parts can make sense on a tight budget or when a part is discontinued, though tolerances, materials and warranty may differ. You decide, and you see the difference on the quote: OEM parts are charged at purchase cost plus a handling fee, while compatible parts usually cost less.

06 · Submission

Getting Your Files to Us

You don’t need a special setup. We accept open files from 3Shape TRIOS, Medit, iTero, CEREC/Sirona, Shining3D Aoralscan and Planmeca systems, in STL, PLY, OBJ, DCM or 3OXZ format. Physical impressions and implant models with analogs are welcome too.

For a smooth first case, send:

  • An intraoral scan with the scan body fully seated, plus the opposing arch and bite
  • Implant brand, model and a photo of the label
  • Soft tissue information or a scan of the tissue cuff
  • Smile, occlusion and shade photos
  • Your prescription, including retention type and component choice

We usually confirm within one working day whether your scan is usable. Your files are used for your case only, never to train software.

Ready to try us? Submit one implant full zirconia crown with your scan and implant details.

07 · Terms

Timing, Remakes and Warranty

Lead times are counted in working days from receipt of the case. In a staged implant case, a custom abutment takes 3–4 working days and final full zirconia 3–5; complex implant cases take 5–7. Clients sending 10 or more cases a month get free rush service, with a guaranteed ship date.

If a crown doesn’t seat, has an open margin or contact, high occlusion or the wrong shade, tell us within 24 hours with photos and we’ll adjust or remake it free. Remakes ship back at our cost. Implant component costs aren’t part of a free remake, and neither are changes to shade or material requested after the order.

08 · Consistency

Your Hundredth Case, Like Your First

A good first case only matters if the next ones match it. Your occlusion, contact, margin and esthetic preferences are saved to your file and applied to every new case, with separate notes for each dentist in a group. You have a responsible manager and a customer service team, and larger clients can have a fixed technician team.

Every case carries a unique number tied to the technician, equipment, material batch and inspection results. If something isn’t right, we can trace it and fix the cause, not only the crown.

Istar Digital is an FDA-registered establishment, Registration Number 3039441248, which you can check in the FDA Establishment Registration & Device Listing database. In the EU, our custom-made restorations follow the MDR custom-made device procedure, and the lab holds ISO 13485. Registration and listing are not FDA approval.

FAQ

Frequently Asked Questions

Can you make an implant full zirconia crown for an anterior tooth?

Yes. Multilayer zirconia is the usual choice for anterior full zirconia. If esthetics come first, layered zirconia may suit the case better. Send shade photos with the target tooth, adjacent teeth and shade tab in the same frame.

Yes. We accept VPS, condensation silicone and polyether impressions, and implant models with analogs. Please use a VPS or polyether bite record rather than wax, which can deform in transit.

No. Single trial cases are welcome, and many new clients start with one. Ongoing partnerships work best with a regular case flow.

Yes. Note the parts you need on the order. Ti-bases, multi-unit abutments and related components are available and appear as separate items on your quote.

Yes. Choose design only, milling and sintering, or complete production. We accept editable 3Shape and exocad files and never contact your dentist clients. We can ship directly to the address you name, although the sender address on the waybill can’t be changed.

Start With One Implant Full Zirconia Crown

The best way to judge a lab is with a real case. Send us one implant crown, compare the fit and finish with what you get today, and decide from there. We’ll review your files, flag anything that could cause trouble and send an itemized quote before we start.

Our team replies in English, usually within an hour during working hours (9:30 am to 6:00 pm China time, UTC+8), with extended support until midnight for urgent cases.